Leak Detection in Herriman, Utah

Yes. We connect Herriman property owners and homeowners in Salt Lake County with licensed leak detection specialists. Our network covers all of Utah and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Elevated water pressure in Herriman accelerates wear on supply line fittings, appliance connections, and fixture valves. Salt Lake County municipal systems can deliver pressure above 80 PSI — above the recommended residential range of 40–60 PSI. High-pressure systems increase the risk of pinhole leaks, fitting failures, and appliance line ruptures. If your water bill is unexpectedly high, a pressure-related hidden leak is a common cause.

Summer creates several distinct leak drivers that make July and August peak months for certain leak types: (1) Peak water demand — irrigation, pools, and increased usage push system pressure to seasonal highs that stress aging pipe fittings; (2) Soil desiccation — in clay soil regions, summer drought causes maximum shrinkage, creating soil movement that stresses slab-embedded and buried pipes; (3) Thermal expansion — copper supply lines experience their maximum annual thermal expansion in summer, stressing joints; (4) Irrigation system activation — irrigation systems that have been off all winter often reveal cracked heads, failed zone valves, and failed backflow preventers when restarted in spring/summer; (5) Pool and outdoor plumbing use — outdoor plumbing that is inactive in winter begins operating again, and winter-damaged fittings fail under pressure.

Ground penetrating radar (GPR) sends electromagnetic pulses into the ground and measures the reflected signals from density changes in subsurface materials. In leak detection, it serves two specific uses: (1) locating buried pipe runs before excavation — GPR can map the horizontal position and depth of underground pipes, helping technicians excavate precisely; (2) detecting voids or soil saturation anomalies that indicate long-standing leaks — water-saturated soil has a different electromagnetic signature than dry soil, allowing GPR to identify leak-affected zones even when the exact pipe location is unknown. GPR is typically used as a supplementary tool alongside acoustic or tracer gas detection, not as a standalone leak detection method.

Commercial leak detection differs from residential in scale, system complexity, and financial exposure. Key differences: (1) Multiple supply zones — commercial buildings often have multiple floors, zones, and dedicated risers that require systematic zone isolation before locating a leak; (2) Shared utility metering — many commercial buildings have a single master meter, making individual unit leak identification require sub-metering or zone isolation valves; (3) Higher pipe complexity — fire suppression systems, chilled water lines, steam lines, and condenser water loops add leak exposure beyond domestic water; (4) Business interruption — a commercial leak may require closing a tenant space during repair, adding business interruption cost to the property damage; (5) Landlord-tenant responsibility — lease agreements determine who bears the cost of leak detection and repair, and terms vary widely; (6) Insurance considerations — commercial property insurance has different sublimits and deductibles than residential, and business interruption coverage adds a separate coverage layer.

The Uniform Plumbing Code and International Plumbing Code both specify a maximum service pressure of 80 PSI for residential supply systems. Most appliance manufacturers void warranties on washing machine hoses, refrigerator water lines, and water heater supply valves at pressures above 80 PSI. Dishwasher fill valves and toilet fill valves are similarly rated for 80 PSI maximum. The optimal range for residential plumbing is 50–70 PSI — sufficient for good shower pressure and appliance performance while keeping stress on fittings and fixtures within safe limits. Below 40 PSI, shower performance degrades and some appliances may not fill correctly. Testing water pressure requires a simple gauge threaded onto a hose bib — available for under $15 at any home improvement store.

A pressure reducing valve (PRV) is installed on the main water supply line entering the home to regulate incoming municipal water pressure down to a safe residential range (typically 60–80 PSI). Without a PRV, homes in high-pressure service zones (hillside neighborhoods, pump-boosted areas) can experience pressures of 100–150 PSI — far above what residential plumbing is designed for. PRV failure is a primary cause of pinhole leaks, appliance hose failures, and fixture seal failures. Signs of PRV failure: water pressure that feels excessively forceful, banging pipes (water hammer), repeatedly failing appliance supply hoses, or a water pressure gauge reading above 80 PSI. PRVs have a typical service life of 10–15 years and should be replaced proactively. Homes without a PRV in a high-pressure zone should have one installed — the cost is $250–$500 installed and can prevent thousands in damage.

Yes — and this is a frequently overlooked risk. An in-ground pool that develops a structural leak can introduce hundreds of gallons per day into the surrounding soil. In expansive clay soils, this causes chronic soil saturation that keeps the clay in a swollen state — which can destabilize adjacent foundation footings and slabs. In sandy or permeable soils, continuous pool leak flow can wash soil away from beneath adjacent structures, causing settlement. Pool leaks typically go undiagnosed because pool owners attribute water loss to evaporation — but evaporation rarely exceeds 1/4 inch per day, while pool leaks can exceed 1 inch per day. The bucket test (floating a bucket of water in the pool for 24 hours and comparing the drop in pool level to the drop in bucket level) is the standard homeowner self-test for pool leak identification.

Galvanized pipes are not immediately dangerous in the way a gas leak is — they present a gradual risk that worsens over time. Galvanized steel pipe corrodes from the inside out. As zinc coating dissolves (typically after 40–50 years), rust accumulates on pipe walls, progressively reducing water flow, discoloring water, and ultimately causing pinhole failures or joint failures. The primary risks are: (1) water quality — orange or rust-colored water from galvanized pipes is a documented health concern as the rust can harbor bacteria and introduces iron above EPA aesthetic limits; (2) reduced flow — heavy rust buildup can reduce pipe diameter by 50–70% in severely corroded runs; (3) lead contamination risk — galvanized pipe used downstream of lead service lines can adsorb and release lead, a documented issue in cities with older municipal infrastructure. Homes with galvanized supply lines more than 50 years old should have them evaluated for replacement.

Tree roots are a primary cause of sewer and drain line failure but rarely breach pressurized supply lines directly. The mechanism differs by line type: For drain and sewer lines — roots seek moisture and enter through pipe joints, cracks, or defects in clay tile, cast iron, concrete, or Orangeburg pipe. Once inside, they grow to fill the pipe diameter. For supply lines — roots can encircle and compress older metallic pipes over decades, causing deformation at joints. They can also cause joint separation through root growth pressure, particularly in older galvanized or lead pipe systems. For irrigation lines — roots seeking moisture are a common cause of drip emitter failure and shallow poly pipe breaches. The tree root risk radius is approximately equal to the tree's drip line (the canopy edge) for actively growing roots, but larger established root systems may extend 2–3× the drip line.