Leak Detection in Highland, Utah

Yes. We connect Highland property owners and homeowners in Utah County with licensed leak detection specialists. Our network covers all of Utah and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Elevated water pressure in Highland accelerates wear on supply line fittings, appliance connections, and fixture valves. Utah County municipal systems can deliver pressure above 80 PSI — above the recommended residential range of 40–60 PSI. High-pressure systems increase the risk of pinhole leaks, fitting failures, and appliance line ruptures. If your water bill is unexpectedly high, a pressure-related hidden leak is a common cause.

A pressure reducing valve (PRV) is installed on the main water supply line entering the home to regulate incoming municipal water pressure down to a safe residential range (typically 60–80 PSI). Without a PRV, homes in high-pressure service zones (hillside neighborhoods, pump-boosted areas) can experience pressures of 100–150 PSI — far above what residential plumbing is designed for. PRV failure is a primary cause of pinhole leaks, appliance hose failures, and fixture seal failures. Signs of PRV failure: water pressure that feels excessively forceful, banging pipes (water hammer), repeatedly failing appliance supply hoses, or a water pressure gauge reading above 80 PSI. PRVs have a typical service life of 10–15 years and should be replaced proactively. Homes without a PRV in a high-pressure zone should have one installed — the cost is $250–$500 installed and can prevent thousands in damage.

Pipe freeze prevention depends on your home's construction type and local frost depth. For all homes: (1) Know where your main shutoff valve is and confirm it operates before winter; (2) Disconnect and drain garden hoses from exterior hose bibs — a connected hose traps water in the spigot and can freeze back into the supply line; (3) Insulate pipes in unheated spaces — garages, crawlspaces, and unconditioned attics. For homes in regions with frost depths below 15 inches (most of the South): (4) Let faucets drip slightly during freeze events — moving water is harder to freeze; (5) Open cabinet doors under sinks on exterior walls to allow heated room air to reach the pipes. For crawlspace homes: (6) Seal crawlspace vents before first freeze to trap ground warmth. For vacant properties: (7) Maintain minimum 55°F interior temperature or fully drain and blow out the supply system with compressed air.

Texas has the highest rate of residential slab leak detection calls of any US state, driven by a specific combination of factors: (1) Soil — the Texas Blackland Prairie and Gulf Coast Prairies sit on Vertisol clay soils with Plasticity Index values of 40–65, among the highest shrink-swell potential soils in the world. These soils undergo 3–6 inches of vertical movement per year between wet and dry seasons. (2) Construction — approximately 95% of Texas homes are built on slab foundations directly in contact with this soil, placing copper supply pipes in direct contact with soil that is constantly moving. (3) Climate — Texas experiences extended summer droughts that maximize soil desiccation and movement, followed by heavy rainfall that causes rapid re-expansion. (4) Pipe era — the bulk of the Texas housing stock was built between 1960 and 1990 with copper supply pipe that now has 30–60 years of service on highly mobile soil.

Orangeburg pipe (also called bituminous fiber pipe) is a drain and sewer pipe made from layers of wood pulp and pitch, manufactured from the 1860s through the 1970s. It was widely used as drain and sewer pipe in homes built before 1970 because it was inexpensive and easy to cut. The problem: Orangeburg was designed with an expected service life of 50 years, and that life is now long expired. It absorbs moisture over time, which causes it to deform from a round cross-section to an oval or collapsed shape. Once deformed, it can no longer carry sewage effectively, and complete collapse follows. Homes built before 1970 — particularly in the Northeast and Midwest — have a high probability of having Orangeburg sewer laterals. A sewer camera inspection is the definitive test.

A sewer camera inspection uses a waterproof camera mounted on a flexible rod to visually inspect the interior of drain and sewer lines. It can identify: (1) root intrusion — tree and shrub roots entering pipe joints, which is the most common cause of sewer line failure; (2) pipe offset or separation at joints from soil settlement; (3) cracks, holes, or completely collapsed sections; (4) grease accumulation or debris blockages; (5) Orangeburg pipe deformation; (6) bellying — sections of pipe that have sagged and create standing water pools that trap solids. The camera records video with a distance marker so the technician can report the exact depth and distance of any defect for excavation planning. Most inspections also include a locator signal from the camera head so the position can be marked at the surface.

The Uniform Plumbing Code and International Plumbing Code both specify a maximum service pressure of 80 PSI for residential supply systems. Most appliance manufacturers void warranties on washing machine hoses, refrigerator water lines, and water heater supply valves at pressures above 80 PSI. Dishwasher fill valves and toilet fill valves are similarly rated for 80 PSI maximum. The optimal range for residential plumbing is 50–70 PSI — sufficient for good shower pressure and appliance performance while keeping stress on fittings and fixtures within safe limits. Below 40 PSI, shower performance degrades and some appliances may not fill correctly. Testing water pressure requires a simple gauge threaded onto a hose bib — available for under $15 at any home improvement store.

Polybutylene pipe is identifiable by its gray, blue, or black color — gray is most common for interior supply lines. Look under sinks, behind the water heater, and at the point where pipes enter walls. The pipe is typically 1/2 inch or 3/4 inch diameter with a dull, matte surface. Fittings are usually gray or white plastic (acetal) or aluminum. If your home was built between 1978 and 1995 and you see gray plastic supply lines, it is almost certainly polybutylene. You can also check the pipe labeling — polybutylene is often stamped 'PB2110'. If confirmed, consult with a licensed plumber about your replacement options — polybutylene was the subject of a class action settlement (Cox v. Shell Oil) specifically because of its documented failure rate.

The timing depends on your primary risk profile. For freeze-risk regions (Midwest, Northeast, Mountain): late fall (October–November) before the first hard freeze is ideal for identifying vulnerable pipe sections before they are stressed. For clay soil regions (Texas, Oklahoma, Kansas, Alabama): late summer or early fall, after peak soil desiccation has maximized stress on slab pipes. For irrigation-heavy regions: early spring before irrigation systems are activated, when damaged components from the previous season can be identified before they cause water loss all summer. For all regions: the best practical answer is as soon as you notice any indicator — water bill increase, discolored water, running water sounds, unexplained moisture. Waiting for a 'good time' often means waiting until the leak has grown.