Leak Detection in South Jordan, Utah

Yes. We connect South Jordan property owners and homeowners in Salt Lake County with licensed leak detection specialists. Our network covers all of Utah and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Elevated water pressure in South Jordan accelerates wear on supply line fittings, appliance connections, and fixture valves. Salt Lake County municipal systems can deliver pressure above 80 PSI — above the recommended residential range of 40–60 PSI. High-pressure systems increase the risk of pinhole leaks, fitting failures, and appliance line ruptures. If your water bill is unexpectedly high, a pressure-related hidden leak is a common cause.

Copper pipe lifespan ranges from 20 to 70+ years depending on water chemistry, installation quality, and environmental conditions. Under ideal conditions — neutral pH water, stable soil, and no mechanical stress — copper can last 50–70 years. Failure is accelerated by: low pH water (below 7.0), which causes pitting corrosion; high chloramine levels from municipal water treatment, which attacks copper from the inside; direct contact with concrete in slab installations (alkaline pH); and soil-to-pipe contact for underground runs. Cities with aggressive water chemistry often see premature pinhole failures in 20–30 year old copper. Cities with neutral chemistry may see the same pipe run 60+ years. The inspection of blue-green staining around fittings or blue-green discoloration in water is the primary visible indicator of active copper corrosion.

Underground service line leaks are among the most expensive and least obvious leaks to identify. Signs include: (1) the water meter test shows movement with all interior fixtures off, but closing the main shutoff inside the house (which leaves only the underground service line pressurized) still shows meter movement — this isolates the leak to the underground run; (2) wet or unusually green patches in the yard that persist regardless of irrigation or rainfall; (3) a sinkhole or soft depression in the yard or driveway; (4) reduced water pressure throughout the house without an identifiable interior cause; (5) water seeping up through cracks in a driveway or sidewalk above where the service line is buried. Professional detection uses acoustic listening rods placed on the pipe at the meter and at the house entry point, or tracer gas introduced into the isolated line.

A pressure reducing valve (PRV) is installed on the main water supply line entering the home to regulate incoming municipal water pressure down to a safe residential range (typically 60–80 PSI). Without a PRV, homes in high-pressure service zones (hillside neighborhoods, pump-boosted areas) can experience pressures of 100–150 PSI — far above what residential plumbing is designed for. PRV failure is a primary cause of pinhole leaks, appliance hose failures, and fixture seal failures. Signs of PRV failure: water pressure that feels excessively forceful, banging pipes (water hammer), repeatedly failing appliance supply hoses, or a water pressure gauge reading above 80 PSI. PRVs have a typical service life of 10–15 years and should be replaced proactively. Homes without a PRV in a high-pressure zone should have one installed — the cost is $250–$500 installed and can prevent thousands in damage.

Thermal imaging cameras detect temperature differences on surfaces — they do not directly see water or pipes. Their value in leak detection comes from the thermal anomalies that active leaks create: (1) a hot water line leak behind a wall creates a warm zone visible as a bright spot on a thermal image; (2) a cold water leak creates a cool evaporative zone as moisture evaporates; (3) saturated insulation retains temperature differently than dry insulation, creating visible boundaries. Thermal imaging is particularly effective for: ceiling leaks from above (roof or plumbing), radiant floor heating system breaches, and locating the extent of moisture intrusion in walls after a known leak. Limitations: thermal imaging cannot locate leaks behind thick concrete slabs or deep underground, and it requires a temperature differential to be effective — in moderate temperatures, the signal may be too weak.

Ground penetrating radar (GPR) sends electromagnetic pulses into the ground and measures the reflected signals from density changes in subsurface materials. In leak detection, it serves two specific uses: (1) locating buried pipe runs before excavation — GPR can map the horizontal position and depth of underground pipes, helping technicians excavate precisely; (2) detecting voids or soil saturation anomalies that indicate long-standing leaks — water-saturated soil has a different electromagnetic signature than dry soil, allowing GPR to identify leak-affected zones even when the exact pipe location is unknown. GPR is typically used as a supplementary tool alongside acoustic or tracer gas detection, not as a standalone leak detection method.

Texas has the highest rate of residential slab leak detection calls of any US state, driven by a specific combination of factors: (1) Soil — the Texas Blackland Prairie and Gulf Coast Prairies sit on Vertisol clay soils with Plasticity Index values of 40–65, among the highest shrink-swell potential soils in the world. These soils undergo 3–6 inches of vertical movement per year between wet and dry seasons. (2) Construction — approximately 95% of Texas homes are built on slab foundations directly in contact with this soil, placing copper supply pipes in direct contact with soil that is constantly moving. (3) Climate — Texas experiences extended summer droughts that maximize soil desiccation and movement, followed by heavy rainfall that causes rapid re-expansion. (4) Pipe era — the bulk of the Texas housing stock was built between 1960 and 1990 with copper supply pipe that now has 30–60 years of service on highly mobile soil.

A sewer camera inspection uses a waterproof camera mounted on a flexible rod to visually inspect the interior of drain and sewer lines. It can identify: (1) root intrusion — tree and shrub roots entering pipe joints, which is the most common cause of sewer line failure; (2) pipe offset or separation at joints from soil settlement; (3) cracks, holes, or completely collapsed sections; (4) grease accumulation or debris blockages; (5) Orangeburg pipe deformation; (6) bellying — sections of pipe that have sagged and create standing water pools that trap solids. The camera records video with a distance marker so the technician can report the exact depth and distance of any defect for excavation planning. Most inspections also include a locator signal from the camera head so the position can be marked at the surface.

Orangeburg pipe (also called bituminous fiber pipe) is a drain and sewer pipe made from layers of wood pulp and pitch, manufactured from the 1860s through the 1970s. It was widely used as drain and sewer pipe in homes built before 1970 because it was inexpensive and easy to cut. The problem: Orangeburg was designed with an expected service life of 50 years, and that life is now long expired. It absorbs moisture over time, which causes it to deform from a round cross-section to an oval or collapsed shape. Once deformed, it can no longer carry sewage effectively, and complete collapse follows. Homes built before 1970 — particularly in the Northeast and Midwest — have a high probability of having Orangeburg sewer laterals. A sewer camera inspection is the definitive test.