Leak Detection in Midway, Utah

Yes. We connect Midway property owners and homeowners in Wasatch County with licensed leak detection specialists. Our network covers all of Utah and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Elevated water pressure in Midway accelerates wear on supply line fittings, appliance connections, and fixture valves. Wasatch County municipal systems can deliver pressure above 80 PSI — above the recommended residential range of 40–60 PSI. High-pressure systems increase the risk of pinhole leaks, fitting failures, and appliance line ruptures. If your water bill is unexpectedly high, a pressure-related hidden leak is a common cause.

Galvanized pipes are not immediately dangerous in the way a gas leak is — they present a gradual risk that worsens over time. Galvanized steel pipe corrodes from the inside out. As zinc coating dissolves (typically after 40–50 years), rust accumulates on pipe walls, progressively reducing water flow, discoloring water, and ultimately causing pinhole failures or joint failures. The primary risks are: (1) water quality — orange or rust-colored water from galvanized pipes is a documented health concern as the rust can harbor bacteria and introduces iron above EPA aesthetic limits; (2) reduced flow — heavy rust buildup can reduce pipe diameter by 50–70% in severely corroded runs; (3) lead contamination risk — galvanized pipe used downstream of lead service lines can adsorb and release lead, a documented issue in cities with older municipal infrastructure. Homes with galvanized supply lines more than 50 years old should have them evaluated for replacement.

Tracer gas detection introduces a non-toxic, non-flammable gas mixture (95% nitrogen / 5% hydrogen) into the water pipe system after water is drained. The gas molecules are extremely small — smaller than water molecules — and escape through the breach point and permeate up through soil and concrete. A technician sweeps the floor surface with a calibrated hydrogen sensor that detects even trace concentrations of the tracer gas. A peak reading identifies the leak location. The 5% hydrogen mixture is specifically chosen because it is below the flammability threshold (hydrogen requires 4–75% concentration in air to ignite), making it completely safe. Tracer gas detection works on any pipe material, making it the preferred method when acoustic detection cannot produce a clear signal — particularly with PEX pipe or when the leak is very small.

Tree roots are a primary cause of sewer and drain line failure but rarely breach pressurized supply lines directly. The mechanism differs by line type: For drain and sewer lines — roots seek moisture and enter through pipe joints, cracks, or defects in clay tile, cast iron, concrete, or Orangeburg pipe. Once inside, they grow to fill the pipe diameter. For supply lines — roots can encircle and compress older metallic pipes over decades, causing deformation at joints. They can also cause joint separation through root growth pressure, particularly in older galvanized or lead pipe systems. For irrigation lines — roots seeking moisture are a common cause of drip emitter failure and shallow poly pipe breaches. The tree root risk radius is approximately equal to the tree's drip line (the canopy edge) for actively growing roots, but larger established root systems may extend 2–3× the drip line.

Expansive soil (also called shrink-swell soil) is soil with a high clay mineral content — specifically smectite and montmorillonite clay minerals — that absorbs water and swells, then dries and contracts. The degree of movement is measured by the Plasticity Index (PI): a PI above 30 is considered high, above 40 very high. For buried and slab-embedded pipes, this movement creates: (1) bending stress as the soil moves laterally or vertically; (2) abrasion as soil particles move against the pipe exterior; (3) joint stress at fittings, which are the weakest points in any pipe run. Copper pipe is particularly vulnerable because it cannot flex to accommodate movement — even small angular deflections at joints cause micro-fracturing that propagates over years of repeated cycles. PEX pipe's flexibility makes it significantly more resistant to expansive soil damage.

Thermal imaging cameras detect temperature differences on surfaces — they do not directly see water or pipes. Their value in leak detection comes from the thermal anomalies that active leaks create: (1) a hot water line leak behind a wall creates a warm zone visible as a bright spot on a thermal image; (2) a cold water leak creates a cool evaporative zone as moisture evaporates; (3) saturated insulation retains temperature differently than dry insulation, creating visible boundaries. Thermal imaging is particularly effective for: ceiling leaks from above (roof or plumbing), radiant floor heating system breaches, and locating the extent of moisture intrusion in walls after a known leak. Limitations: thermal imaging cannot locate leaks behind thick concrete slabs or deep underground, and it requires a temperature differential to be effective — in moderate temperatures, the signal may be too weak.

Responsibility is typically split at the water meter, which sits at or near the property line. The municipal water utility owns and maintains everything from the water main in the street to the meter. The homeowner owns and is responsible for everything from the meter to the house — including the full underground service line run across the property. This is an important distinction because service line leaks on the homeowner's side are the homeowner's financial responsibility, and standard homeowners insurance (HO-3 policies) does not cover underground service line repair by default. A service line insurance endorsement — available from most insurers for $30–$60 per year — extends coverage to this exposure. Some utilities have begun offering service line protection programs as a billing add-on.

A sewer camera inspection uses a waterproof camera mounted on a flexible rod to visually inspect the interior of drain and sewer lines. It can identify: (1) root intrusion — tree and shrub roots entering pipe joints, which is the most common cause of sewer line failure; (2) pipe offset or separation at joints from soil settlement; (3) cracks, holes, or completely collapsed sections; (4) grease accumulation or debris blockages; (5) Orangeburg pipe deformation; (6) bellying — sections of pipe that have sagged and create standing water pools that trap solids. The camera records video with a distance marker so the technician can report the exact depth and distance of any defect for excavation planning. Most inspections also include a locator signal from the camera head so the position can be marked at the surface.

Private service line failures (the homeowner's underground water line) are caused by: (1) pipe material age — galvanized steel and lead service lines installed in homes before 1960 are past designed service life; (2) soil movement — freeze-thaw cycling and expansive clay movement stress pipe joints repeatedly until failure; (3) tree root intrusion — roots follow moisture and can encircle and crush or pierce service lines, particularly older clay or galvanized lines; (4) external loading — heavy vehicles driving over a shallow-buried service line, or settlement of pavement above it; (5) electrolytic corrosion — stray electrical currents in the soil accelerate corrosion of metallic pipes. Plastic pipes (PVC, PEX) are significantly more resistant to all of these failure modes than older metallic pipe materials.