Leak Detection in Portsmouth, New Hampshire

Yes. We connect Portsmouth property owners and homeowners in Rockingham County with licensed leak detection specialists. Our network covers all of New Hampshire and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

In Portsmouth, pipes in unheated spaces — crawlspaces, garages, exterior walls — are most vulnerable during hard freezes. A pipe that freezes may not burst immediately; freeze-thaw cycling creates micro-fractures that fail days or weeks later. If you experienced a freeze event and notice reduced pressure or unexplained moisture in Rockingham County, professional leak detection can find damage before it becomes a larger structural problem.

Yes — and this is a frequently overlooked risk. An in-ground pool that develops a structural leak can introduce hundreds of gallons per day into the surrounding soil. In expansive clay soils, this causes chronic soil saturation that keeps the clay in a swollen state — which can destabilize adjacent foundation footings and slabs. In sandy or permeable soils, continuous pool leak flow can wash soil away from beneath adjacent structures, causing settlement. Pool leaks typically go undiagnosed because pool owners attribute water loss to evaporation — but evaporation rarely exceeds 1/4 inch per day, while pool leaks can exceed 1 inch per day. The bucket test (floating a bucket of water in the pool for 24 hours and comparing the drop in pool level to the drop in bucket level) is the standard homeowner self-test for pool leak identification.

Condo water leak responsibility is governed by the condominium's declaration documents (CC&Rs) and the master insurance policy, not a universal rule. Generally: (1) If a leak originates in a unit's exclusive-use plumbing (fixture, supply line within the unit) and damages a neighboring unit, the unit owner at the source is typically liable; (2) If the leak comes from common-area plumbing (building supply risers, shared drain stacks), the HOA or condo association is typically responsible; (3) The boundary between unit plumbing and common area plumbing varies by building — some documents define the unit boundary at the drywall face, others at the pipe centerline; (4) Master insurance policies cover damage to common areas; individual HO-6 policies cover unit interiors. A unit-to-unit water damage dispute often involves both insurance carriers and requires a professional detection report establishing where the leak originated to allocate responsibility.

Polybutylene pipe is identifiable by its gray, blue, or black color — gray is most common for interior supply lines. Look under sinks, behind the water heater, and at the point where pipes enter walls. The pipe is typically 1/2 inch or 3/4 inch diameter with a dull, matte surface. Fittings are usually gray or white plastic (acetal) or aluminum. If your home was built between 1978 and 1995 and you see gray plastic supply lines, it is almost certainly polybutylene. You can also check the pipe labeling — polybutylene is often stamped 'PB2110'. If confirmed, consult with a licensed plumber about your replacement options — polybutylene was the subject of a class action settlement (Cox v. Shell Oil) specifically because of its documented failure rate.

Galvanized pipes are not immediately dangerous in the way a gas leak is — they present a gradual risk that worsens over time. Galvanized steel pipe corrodes from the inside out. As zinc coating dissolves (typically after 40–50 years), rust accumulates on pipe walls, progressively reducing water flow, discoloring water, and ultimately causing pinhole failures or joint failures. The primary risks are: (1) water quality — orange or rust-colored water from galvanized pipes is a documented health concern as the rust can harbor bacteria and introduces iron above EPA aesthetic limits; (2) reduced flow — heavy rust buildup can reduce pipe diameter by 50–70% in severely corroded runs; (3) lead contamination risk — galvanized pipe used downstream of lead service lines can adsorb and release lead, a documented issue in cities with older municipal infrastructure. Homes with galvanized supply lines more than 50 years old should have them evaluated for replacement.

A moving meter with no visible leak almost always means the leak is hidden — either inside walls, under the slab, underground between the meter and the house, or in an irrigation system branch. The most common locations for hidden leaks detected this way are: (1) slab supply lines under the concrete floor; (2) underground service line between the meter and the house foundation; (3) toilet flappers (though these are more commonly caught by dye testing than meter observation); (4) outdoor irrigation zone valves that fail to close fully. The next diagnostic step is to isolate the leak to a specific zone by closing the main shutoff valve inside the house and observing whether the meter continues to move — if it does, the leak is between the meter and the house on the service line.

Summer creates several distinct leak drivers that make July and August peak months for certain leak types: (1) Peak water demand — irrigation, pools, and increased usage push system pressure to seasonal highs that stress aging pipe fittings; (2) Soil desiccation — in clay soil regions, summer drought causes maximum shrinkage, creating soil movement that stresses slab-embedded and buried pipes; (3) Thermal expansion — copper supply lines experience their maximum annual thermal expansion in summer, stressing joints; (4) Irrigation system activation — irrigation systems that have been off all winter often reveal cracked heads, failed zone valves, and failed backflow preventers when restarted in spring/summer; (5) Pool and outdoor plumbing use — outdoor plumbing that is inactive in winter begins operating again, and winter-damaged fittings fail under pressure.

Tracer gas detection introduces a non-toxic, non-flammable gas mixture (95% nitrogen / 5% hydrogen) into the water pipe system after water is drained. The gas molecules are extremely small — smaller than water molecules — and escape through the breach point and permeate up through soil and concrete. A technician sweeps the floor surface with a calibrated hydrogen sensor that detects even trace concentrations of the tracer gas. A peak reading identifies the leak location. The 5% hydrogen mixture is specifically chosen because it is below the flammability threshold (hydrogen requires 4–75% concentration in air to ignite), making it completely safe. Tracer gas detection works on any pipe material, making it the preferred method when acoustic detection cannot produce a clear signal — particularly with PEX pipe or when the leak is very small.

Thermal imaging cameras detect temperature differences on surfaces — they do not directly see water or pipes. Their value in leak detection comes from the thermal anomalies that active leaks create: (1) a hot water line leak behind a wall creates a warm zone visible as a bright spot on a thermal image; (2) a cold water leak creates a cool evaporative zone as moisture evaporates; (3) saturated insulation retains temperature differently than dry insulation, creating visible boundaries. Thermal imaging is particularly effective for: ceiling leaks from above (roof or plumbing), radiant floor heating system breaches, and locating the extent of moisture intrusion in walls after a known leak. Limitations: thermal imaging cannot locate leaks behind thick concrete slabs or deep underground, and it requires a temperature differential to be effective — in moderate temperatures, the signal may be too weak.