Leak Detection in North Conway, New Hampshire

Yes. We connect North Conway property owners and homeowners in Carroll County with licensed leak detection specialists. Our network covers all of New Hampshire and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

In North Conway, pipes in unheated spaces — crawlspaces, garages, exterior walls — are most vulnerable during hard freezes. A pipe that freezes may not burst immediately; freeze-thaw cycling creates micro-fractures that fail days or weeks later. If you experienced a freeze event and notice reduced pressure or unexplained moisture in Carroll County, professional leak detection can find damage before it becomes a larger structural problem.

A moving meter with no visible leak almost always means the leak is hidden — either inside walls, under the slab, underground between the meter and the house, or in an irrigation system branch. The most common locations for hidden leaks detected this way are: (1) slab supply lines under the concrete floor; (2) underground service line between the meter and the house foundation; (3) toilet flappers (though these are more commonly caught by dye testing than meter observation); (4) outdoor irrigation zone valves that fail to close fully. The next diagnostic step is to isolate the leak to a specific zone by closing the main shutoff valve inside the house and observing whether the meter continues to move — if it does, the leak is between the meter and the house on the service line.

A pressure reducing valve (PRV) is installed on the main water supply line entering the home to regulate incoming municipal water pressure down to a safe residential range (typically 60–80 PSI). Without a PRV, homes in high-pressure service zones (hillside neighborhoods, pump-boosted areas) can experience pressures of 100–150 PSI — far above what residential plumbing is designed for. PRV failure is a primary cause of pinhole leaks, appliance hose failures, and fixture seal failures. Signs of PRV failure: water pressure that feels excessively forceful, banging pipes (water hammer), repeatedly failing appliance supply hoses, or a water pressure gauge reading above 80 PSI. PRVs have a typical service life of 10–15 years and should be replaced proactively. Homes without a PRV in a high-pressure zone should have one installed — the cost is $250–$500 installed and can prevent thousands in damage.

A sewer camera inspection uses a waterproof camera mounted on a flexible rod to visually inspect the interior of drain and sewer lines. It can identify: (1) root intrusion — tree and shrub roots entering pipe joints, which is the most common cause of sewer line failure; (2) pipe offset or separation at joints from soil settlement; (3) cracks, holes, or completely collapsed sections; (4) grease accumulation or debris blockages; (5) Orangeburg pipe deformation; (6) bellying — sections of pipe that have sagged and create standing water pools that trap solids. The camera records video with a distance marker so the technician can report the exact depth and distance of any defect for excavation planning. Most inspections also include a locator signal from the camera head so the position can be marked at the surface.

Acoustic leak detection uses sensitive microphones and electronic amplifiers to hear the sound of pressurized water escaping through a pipe breach. Water escaping under pressure creates a turbulent noise — typically a hiss, rush, or 'white noise' signature — that travels through the pipe material and into surrounding structures. Technicians place ground microphones directly on floor surfaces or use listening rods on accessible pipe sections to amplify and compare signal strength. The leak location is identified as the point of maximum signal intensity. Acoustic detection works best on metallic pipes (copper, galvanized steel) because sound travels efficiently through metal. It is less effective on PEX and CPVC because plastic absorbs sound rather than conducting it — in those cases, tracer gas detection is the preferred alternative.

Pipe freeze prevention depends on your home's construction type and local frost depth. For all homes: (1) Know where your main shutoff valve is and confirm it operates before winter; (2) Disconnect and drain garden hoses from exterior hose bibs — a connected hose traps water in the spigot and can freeze back into the supply line; (3) Insulate pipes in unheated spaces — garages, crawlspaces, and unconditioned attics. For homes in regions with frost depths below 15 inches (most of the South): (4) Let faucets drip slightly during freeze events — moving water is harder to freeze; (5) Open cabinet doors under sinks on exterior walls to allow heated room air to reach the pipes. For crawlspace homes: (6) Seal crawlspace vents before first freeze to trap ground warmth. For vacant properties: (7) Maintain minimum 55°F interior temperature or fully drain and blow out the supply system with compressed air.

A pinhole slab leak under 40–60 PSI system pressure loses approximately 10–30 gallons per hour — or 240–720 gallons per day. A larger failure point at a pipe fitting or elbow can lose significantly more. At the national average water rate of approximately $0.006 per gallon, a mid-range slab leak costs roughly $500–$1,500 per month in wasted water before detection. Beyond water cost, this volume continuously saturates sub-slab soil, which is the mechanism for the foundation damage and mold risk that accompany long-standing undetected leaks.

PEX (cross-linked polyethylene) and copper are the two most common residential supply pipe materials used today. Key differences: (1) Flexibility — PEX is semi-rigid and can be routed around corners without fittings, reducing leak point count; copper is rigid and requires fittings at every bend, each of which is a potential failure point. (2) Freeze resistance — PEX expands under freezing and returns to shape on thaw, dramatically reducing freeze burst risk; copper does not expand and bursts when water freezes inside. (3) Corrosion resistance — PEX is immune to the electrochemical corrosion that causes copper pinholes; copper is susceptible to water chemistry attack. (4) Cost — PEX material is typically 25–40% cheaper than copper. (5) Lifespan — PEX has a projected 50+ year service life with limited field data beyond 25 years; copper has a demonstrated 50–70 year track record. (6) Heat tolerance — copper handles high-temperature water better; PEX has a maximum service temperature of 200°F.

Underground service line leaks are among the most expensive and least obvious leaks to identify. Signs include: (1) the water meter test shows movement with all interior fixtures off, but closing the main shutoff inside the house (which leaves only the underground service line pressurized) still shows meter movement — this isolates the leak to the underground run; (2) wet or unusually green patches in the yard that persist regardless of irrigation or rainfall; (3) a sinkhole or soft depression in the yard or driveway; (4) reduced water pressure throughout the house without an identifiable interior cause; (5) water seeping up through cracks in a driveway or sidewalk above where the service line is buried. Professional detection uses acoustic listening rods placed on the pipe at the meter and at the house entry point, or tracer gas introduced into the isolated line.