Leak Detection in Savannah, Georgia

Yes. We connect Savannah property owners and homeowners in Chatham County with licensed leak detection specialists. Our network covers all of Georgia and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Slab leak signs in Savannah include warm or wet spots on concrete floors, a running water meter with all fixtures off, unusually high water bills, and foundation cracks appearing without an obvious cause. Clay soil movement in Chatham County stresses buried copper lines over time, making slab leaks more common in older slab-on-grade construction. Professional leak detection can confirm or rule out a slab leak without breaking your floor.

Yes — and this is a frequently overlooked risk. An in-ground pool that develops a structural leak can introduce hundreds of gallons per day into the surrounding soil. In expansive clay soils, this causes chronic soil saturation that keeps the clay in a swollen state — which can destabilize adjacent foundation footings and slabs. In sandy or permeable soils, continuous pool leak flow can wash soil away from beneath adjacent structures, causing settlement. Pool leaks typically go undiagnosed because pool owners attribute water loss to evaporation — but evaporation rarely exceeds 1/4 inch per day, while pool leaks can exceed 1 inch per day. The bucket test (floating a bucket of water in the pool for 24 hours and comparing the drop in pool level to the drop in bucket level) is the standard homeowner self-test for pool leak identification.

Yes — and this is the primary reason early detection matters. A pressurized supply line leak under a slab introduces water into the sub-slab soil at a continuous rate. In expansive clay soils, this causes localized soil swelling that can heave the slab unevenly. In sandy or silty soils, it can cause subsidence — the opposite problem, where the soil washes away and the slab loses support. Either scenario produces differential foundation movement, which manifests as sticking doors, diagonal wall cracks, and sloping floors. Foundation damage from an undetected slab leak is typically not covered by standard homeowners insurance as it is classified as ongoing neglect rather than a sudden event.

A moving meter with no visible leak almost always means the leak is hidden — either inside walls, under the slab, underground between the meter and the house, or in an irrigation system branch. The most common locations for hidden leaks detected this way are: (1) slab supply lines under the concrete floor; (2) underground service line between the meter and the house foundation; (3) toilet flappers (though these are more commonly caught by dye testing than meter observation); (4) outdoor irrigation zone valves that fail to close fully. The next diagnostic step is to isolate the leak to a specific zone by closing the main shutoff valve inside the house and observing whether the meter continues to move — if it does, the leak is between the meter and the house on the service line.

Summer creates several distinct leak drivers that make July and August peak months for certain leak types: (1) Peak water demand — irrigation, pools, and increased usage push system pressure to seasonal highs that stress aging pipe fittings; (2) Soil desiccation — in clay soil regions, summer drought causes maximum shrinkage, creating soil movement that stresses slab-embedded and buried pipes; (3) Thermal expansion — copper supply lines experience their maximum annual thermal expansion in summer, stressing joints; (4) Irrigation system activation — irrigation systems that have been off all winter often reveal cracked heads, failed zone valves, and failed backflow preventers when restarted in spring/summer; (5) Pool and outdoor plumbing use — outdoor plumbing that is inactive in winter begins operating again, and winter-damaged fittings fail under pressure.

Professional slab leak detection typically costs $150–$400 for the detection service alone, separate from any repair work. Acoustic electronic detection — the most common method — falls in the $150–$300 range. Tracer gas detection, used when acoustic signals are weak (such as under thick concrete or with PEX pipe), typically runs $250–$400. The detection fee covers locating and marking the leak position to within a few inches, which directly reduces repair excavation costs. Detection cost is a small fraction of total project cost — avoiding unnecessary concrete cutting by knowing the exact leak location typically saves $500–$2,000 in repair labor.

The Uniform Plumbing Code and International Plumbing Code both specify a maximum service pressure of 80 PSI for residential supply systems. Most appliance manufacturers void warranties on washing machine hoses, refrigerator water lines, and water heater supply valves at pressures above 80 PSI. Dishwasher fill valves and toilet fill valves are similarly rated for 80 PSI maximum. The optimal range for residential plumbing is 50–70 PSI — sufficient for good shower pressure and appliance performance while keeping stress on fittings and fixtures within safe limits. Below 40 PSI, shower performance degrades and some appliances may not fill correctly. Testing water pressure requires a simple gauge threaded onto a hose bib — available for under $15 at any home improvement store.

The water meter test is a reliable first step any homeowner can perform without tools. Step 1: Turn off all water fixtures inside and outside the home — including dishwashers, ice makers, and irrigation systems. Step 2: Locate your water meter (typically at the street curb in a covered box). Step 3: Note the meter reading and look for the leak indicator — a small dial, triangle, or star on the meter face that spins with any water movement. Step 4: Wait 15–30 minutes without using any water. Step 5: Check whether the meter reading has changed or the leak indicator is still moving. Any movement with all fixtures off indicates an active leak somewhere between the meter and the home. This test does not locate the leak — it only confirms one exists.

Slab leaks occur when a water supply or drain line embedded in a concrete foundation develops a breach. The three primary causes are: (1) soil movement — expansive clay soils shrink and swell seasonally, stressing pipe joints and bending copper lines over time; (2) pipe corrosion — copper pipes embedded in concrete are exposed to alkaline pH and mineral contact that accelerates pitting; (3) water hammer — repeated pressure surges from rapid valve closures create micro-fractures at elbows and fittings. In cities built on high-shrink-swell Vertisol clay (Houston, Dallas, the Texas Blackland Prairie), soil movement is the dominant cause. In older cities with original copper runs, corrosion-driven pinhole failure is most common.