Leak Detection in Royston, Georgia

Yes. We connect Royston property owners and homeowners in Franklin County with licensed leak detection specialists. Our network covers all of Georgia and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Slab leak signs in Royston include warm or wet spots on concrete floors, a running water meter with all fixtures off, unusually high water bills, and foundation cracks appearing without an obvious cause. Clay soil movement in Franklin County stresses buried copper lines over time, making slab leaks more common in older slab-on-grade construction. Professional leak detection can confirm or rule out a slab leak without breaking your floor.

Homeowners can perform several reliable self-tests that confirm a leak exists: the water meter test (watching for movement after all fixtures are off), a toilet dye test (food coloring in the tank — if color appears in the bowl without flushing, the flapper is leaking), and visual inspection of known failure points (supply hose connections, water heater inlet/outlet, fixture supply valves). What self-tests cannot do is locate a hidden leak to a specific point. Without acoustic or tracer gas equipment, a homeowner who has confirmed via meter test that a supply leak exists cannot determine whether it is under the slab, in a wall, or in the underground service line — and an incorrect diagnosis of a slab leak location can result in unnecessary concrete cutting in the wrong spot. Professional detection is appropriate any time a self-test confirms a leak but the source is not visually obvious.

Professional slab leak detection typically costs $150–$400 for the detection service alone, separate from any repair work. Acoustic electronic detection — the most common method — falls in the $150–$300 range. Tracer gas detection, used when acoustic signals are weak (such as under thick concrete or with PEX pipe), typically runs $250–$400. The detection fee covers locating and marking the leak position to within a few inches, which directly reduces repair excavation costs. Detection cost is a small fraction of total project cost — avoiding unnecessary concrete cutting by knowing the exact leak location typically saves $500–$2,000 in repair labor.

Responsibility is typically split at the water meter, which sits at or near the property line. The municipal water utility owns and maintains everything from the water main in the street to the meter. The homeowner owns and is responsible for everything from the meter to the house — including the full underground service line run across the property. This is an important distinction because service line leaks on the homeowner's side are the homeowner's financial responsibility, and standard homeowners insurance (HO-3 policies) does not cover underground service line repair by default. A service line insurance endorsement — available from most insurers for $30–$60 per year — extends coverage to this exposure. Some utilities have begun offering service line protection programs as a billing add-on.

A pressure reducing valve (PRV) is installed on the main water supply line entering the home to regulate incoming municipal water pressure down to a safe residential range (typically 60–80 PSI). Without a PRV, homes in high-pressure service zones (hillside neighborhoods, pump-boosted areas) can experience pressures of 100–150 PSI — far above what residential plumbing is designed for. PRV failure is a primary cause of pinhole leaks, appliance hose failures, and fixture seal failures. Signs of PRV failure: water pressure that feels excessively forceful, banging pipes (water hammer), repeatedly failing appliance supply hoses, or a water pressure gauge reading above 80 PSI. PRVs have a typical service life of 10–15 years and should be replaced proactively. Homes without a PRV in a high-pressure zone should have one installed — the cost is $250–$500 installed and can prevent thousands in damage.

A moving meter with no visible leak almost always means the leak is hidden — either inside walls, under the slab, underground between the meter and the house, or in an irrigation system branch. The most common locations for hidden leaks detected this way are: (1) slab supply lines under the concrete floor; (2) underground service line between the meter and the house foundation; (3) toilet flappers (though these are more commonly caught by dye testing than meter observation); (4) outdoor irrigation zone valves that fail to close fully. The next diagnostic step is to isolate the leak to a specific zone by closing the main shutoff valve inside the house and observing whether the meter continues to move — if it does, the leak is between the meter and the house on the service line.

Summer creates several distinct leak drivers that make July and August peak months for certain leak types: (1) Peak water demand — irrigation, pools, and increased usage push system pressure to seasonal highs that stress aging pipe fittings; (2) Soil desiccation — in clay soil regions, summer drought causes maximum shrinkage, creating soil movement that stresses slab-embedded and buried pipes; (3) Thermal expansion — copper supply lines experience their maximum annual thermal expansion in summer, stressing joints; (4) Irrigation system activation — irrigation systems that have been off all winter often reveal cracked heads, failed zone valves, and failed backflow preventers when restarted in spring/summer; (5) Pool and outdoor plumbing use — outdoor plumbing that is inactive in winter begins operating again, and winter-damaged fittings fail under pressure.

Water leaks produce secondary odors rather than a direct smell from the water itself. The characteristic musty, earthy odor associated with leaks comes from mold and mildew growth in saturated building materials — typically within 24–72 hours of initial saturation in warm, humid conditions. A more specific sulfurous or sewage odor indicates a drain or sewer leak rather than a supply line leak. In wall or subfloor cavities, the smell of wet wood combined with mold is distinctive — an 'old house' smell concentrated in a specific area often points to an active hidden leak in that zone. Gas lines have an added odorant (mercaptan) that produces a distinct sulfur/rotten egg smell — this is an emergency requiring immediate evacuation and utility contact, not a plumber.

A professional slab leak detection appointment typically takes 1–3 hours on-site. The technician first performs an isolation test to confirm the leak is on the supply side (checking hot and cold lines separately) and to estimate flow rate. Acoustic detection involves placing sensors at multiple points on the floor and listening for the characteristic leak noise amplified through the concrete. In straightforward cases with good acoustic signal, the leak can be located within 60–90 minutes. Complex cases — thick slabs, multiple pipe runs, weak acoustic signal from PEX pipe — may require tracer gas as a secondary method, extending the appointment to 2–3 hours.