Leak Detection in Newnan, Georgia

Yes. We connect Newnan property owners and homeowners in Coweta County with licensed leak detection specialists. Our network covers all of Georgia and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Slab leak signs in Newnan include warm or wet spots on concrete floors, a running water meter with all fixtures off, unusually high water bills, and foundation cracks appearing without an obvious cause. Clay soil movement in Coweta County stresses buried copper lines over time, making slab leaks more common in older slab-on-grade construction. Professional leak detection can confirm or rule out a slab leak without breaking your floor.

The timing depends on your primary risk profile. For freeze-risk regions (Midwest, Northeast, Mountain): late fall (October–November) before the first hard freeze is ideal for identifying vulnerable pipe sections before they are stressed. For clay soil regions (Texas, Oklahoma, Kansas, Alabama): late summer or early fall, after peak soil desiccation has maximized stress on slab pipes. For irrigation-heavy regions: early spring before irrigation systems are activated, when damaged components from the previous season can be identified before they cause water loss all summer. For all regions: the best practical answer is as soon as you notice any indicator — water bill increase, discolored water, running water sounds, unexplained moisture. Waiting for a 'good time' often means waiting until the leak has grown.

Yes — and this is a frequently overlooked risk. An in-ground pool that develops a structural leak can introduce hundreds of gallons per day into the surrounding soil. In expansive clay soils, this causes chronic soil saturation that keeps the clay in a swollen state — which can destabilize adjacent foundation footings and slabs. In sandy or permeable soils, continuous pool leak flow can wash soil away from beneath adjacent structures, causing settlement. Pool leaks typically go undiagnosed because pool owners attribute water loss to evaporation — but evaporation rarely exceeds 1/4 inch per day, while pool leaks can exceed 1 inch per day. The bucket test (floating a bucket of water in the pool for 24 hours and comparing the drop in pool level to the drop in bucket level) is the standard homeowner self-test for pool leak identification.

A moving meter with no visible leak almost always means the leak is hidden — either inside walls, under the slab, underground between the meter and the house, or in an irrigation system branch. The most common locations for hidden leaks detected this way are: (1) slab supply lines under the concrete floor; (2) underground service line between the meter and the house foundation; (3) toilet flappers (though these are more commonly caught by dye testing than meter observation); (4) outdoor irrigation zone valves that fail to close fully. The next diagnostic step is to isolate the leak to a specific zone by closing the main shutoff valve inside the house and observing whether the meter continues to move — if it does, the leak is between the meter and the house on the service line.

Underground service line leaks are among the most expensive and least obvious leaks to identify. Signs include: (1) the water meter test shows movement with all interior fixtures off, but closing the main shutoff inside the house (which leaves only the underground service line pressurized) still shows meter movement — this isolates the leak to the underground run; (2) wet or unusually green patches in the yard that persist regardless of irrigation or rainfall; (3) a sinkhole or soft depression in the yard or driveway; (4) reduced water pressure throughout the house without an identifiable interior cause; (5) water seeping up through cracks in a driveway or sidewalk above where the service line is buried. Professional detection uses acoustic listening rods placed on the pipe at the meter and at the house entry point, or tracer gas introduced into the isolated line.

Yes — most significant leaks are invisible at their source until substantial damage has occurred. Slab leaks are entirely under concrete. Underground service line leaks may not surface for months if the soil has good absorption capacity. Wall leaks from pinhole copper or failed shower pan liners discharge into wall cavities and subfloors, appearing only as staining, bubbling paint, or soft flooring. Leaks in unconditioned attic spaces may not manifest inside the living space until roof deck damage causes secondary intrusion. The absence of visible water is the primary reason leak detection technology exists — the purpose of acoustic, tracer gas, and thermal tools is to locate leaks that cannot be found by looking. An unexplained increase in water consumption confirmed by comparing monthly bills to the same period in prior years is often the only early indicator.

A professional slab leak detection appointment typically takes 1–3 hours on-site. The technician first performs an isolation test to confirm the leak is on the supply side (checking hot and cold lines separately) and to estimate flow rate. Acoustic detection involves placing sensors at multiple points on the floor and listening for the characteristic leak noise amplified through the concrete. In straightforward cases with good acoustic signal, the leak can be located within 60–90 minutes. Complex cases — thick slabs, multiple pipe runs, weak acoustic signal from PEX pipe — may require tracer gas as a secondary method, extending the appointment to 2–3 hours.

Homeowners can perform several reliable self-tests that confirm a leak exists: the water meter test (watching for movement after all fixtures are off), a toilet dye test (food coloring in the tank — if color appears in the bowl without flushing, the flapper is leaking), and visual inspection of known failure points (supply hose connections, water heater inlet/outlet, fixture supply valves). What self-tests cannot do is locate a hidden leak to a specific point. Without acoustic or tracer gas equipment, a homeowner who has confirmed via meter test that a supply leak exists cannot determine whether it is under the slab, in a wall, or in the underground service line — and an incorrect diagnosis of a slab leak location can result in unnecessary concrete cutting in the wrong spot. Professional detection is appropriate any time a self-test confirms a leak but the source is not visually obvious.

The water meter test is a reliable first step any homeowner can perform without tools. Step 1: Turn off all water fixtures inside and outside the home — including dishwashers, ice makers, and irrigation systems. Step 2: Locate your water meter (typically at the street curb in a covered box). Step 3: Note the meter reading and look for the leak indicator — a small dial, triangle, or star on the meter face that spins with any water movement. Step 4: Wait 15–30 minutes without using any water. Step 5: Check whether the meter reading has changed or the leak indicator is still moving. Any movement with all fixtures off indicates an active leak somewhere between the meter and the home. This test does not locate the leak — it only confirms one exists.