Leak Detection in Marietta, Georgia

Yes. We connect Marietta property owners and homeowners in Cobb County with licensed leak detection specialists. Our network covers all of Georgia and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Slab leak signs in Marietta include warm or wet spots on concrete floors, a running water meter with all fixtures off, unusually high water bills, and foundation cracks appearing without an obvious cause. Clay soil movement in Cobb County stresses buried copper lines over time, making slab leaks more common in older slab-on-grade construction. Professional leak detection can confirm or rule out a slab leak without breaking your floor.

Underground service line leaks are among the most expensive and least obvious leaks to identify. Signs include: (1) the water meter test shows movement with all interior fixtures off, but closing the main shutoff inside the house (which leaves only the underground service line pressurized) still shows meter movement — this isolates the leak to the underground run; (2) wet or unusually green patches in the yard that persist regardless of irrigation or rainfall; (3) a sinkhole or soft depression in the yard or driveway; (4) reduced water pressure throughout the house without an identifiable interior cause; (5) water seeping up through cracks in a driveway or sidewalk above where the service line is buried. Professional detection uses acoustic listening rods placed on the pipe at the meter and at the house entry point, or tracer gas introduced into the isolated line.

Expansive soil (also called shrink-swell soil) is soil with a high clay mineral content — specifically smectite and montmorillonite clay minerals — that absorbs water and swells, then dries and contracts. The degree of movement is measured by the Plasticity Index (PI): a PI above 30 is considered high, above 40 very high. For buried and slab-embedded pipes, this movement creates: (1) bending stress as the soil moves laterally or vertically; (2) abrasion as soil particles move against the pipe exterior; (3) joint stress at fittings, which are the weakest points in any pipe run. Copper pipe is particularly vulnerable because it cannot flex to accommodate movement — even small angular deflections at joints cause micro-fracturing that propagates over years of repeated cycles. PEX pipe's flexibility makes it significantly more resistant to expansive soil damage.

A pinhole slab leak under 40–60 PSI system pressure loses approximately 10–30 gallons per hour — or 240–720 gallons per day. A larger failure point at a pipe fitting or elbow can lose significantly more. At the national average water rate of approximately $0.006 per gallon, a mid-range slab leak costs roughly $500–$1,500 per month in wasted water before detection. Beyond water cost, this volume continuously saturates sub-slab soil, which is the mechanism for the foundation damage and mold risk that accompany long-standing undetected leaks.

Slab leaks occur when a water supply or drain line embedded in a concrete foundation develops a breach. The three primary causes are: (1) soil movement — expansive clay soils shrink and swell seasonally, stressing pipe joints and bending copper lines over time; (2) pipe corrosion — copper pipes embedded in concrete are exposed to alkaline pH and mineral contact that accelerates pitting; (3) water hammer — repeated pressure surges from rapid valve closures create micro-fractures at elbows and fittings. In cities built on high-shrink-swell Vertisol clay (Houston, Dallas, the Texas Blackland Prairie), soil movement is the dominant cause. In older cities with original copper runs, corrosion-driven pinhole failure is most common.

The most reliable early indicators are: (1) a water meter that continues to move after all fixtures are turned off — the meter test is the first self-check every homeowner should perform; (2) unexplained increases in your water bill without a change in usage; (3) warm or hot spots on floor surfaces (for hot water line leaks); (4) the sound of running water when no fixture is in use; (5) cracks appearing in interior walls or floor tiles, particularly in a linear pattern following a pipe run. Slab leaks from drain lines may not show water meter movement — instead they present as soft spots in flooring, musty odors, or unexplained moisture at baseboards. A professional acoustic or tracer gas test is needed to pinpoint the exact leak location before any repair.

Yes — most significant leaks are invisible at their source until substantial damage has occurred. Slab leaks are entirely under concrete. Underground service line leaks may not surface for months if the soil has good absorption capacity. Wall leaks from pinhole copper or failed shower pan liners discharge into wall cavities and subfloors, appearing only as staining, bubbling paint, or soft flooring. Leaks in unconditioned attic spaces may not manifest inside the living space until roof deck damage causes secondary intrusion. The absence of visible water is the primary reason leak detection technology exists — the purpose of acoustic, tracer gas, and thermal tools is to locate leaks that cannot be found by looking. An unexplained increase in water consumption confirmed by comparing monthly bills to the same period in prior years is often the only early indicator.

Texas has the highest rate of residential slab leak detection calls of any US state, driven by a specific combination of factors: (1) Soil — the Texas Blackland Prairie and Gulf Coast Prairies sit on Vertisol clay soils with Plasticity Index values of 40–65, among the highest shrink-swell potential soils in the world. These soils undergo 3–6 inches of vertical movement per year between wet and dry seasons. (2) Construction — approximately 95% of Texas homes are built on slab foundations directly in contact with this soil, placing copper supply pipes in direct contact with soil that is constantly moving. (3) Climate — Texas experiences extended summer droughts that maximize soil desiccation and movement, followed by heavy rainfall that causes rapid re-expansion. (4) Pipe era — the bulk of the Texas housing stock was built between 1960 and 1990 with copper supply pipe that now has 30–60 years of service on highly mobile soil.

The water meter test is a reliable first step any homeowner can perform without tools. Step 1: Turn off all water fixtures inside and outside the home — including dishwashers, ice makers, and irrigation systems. Step 2: Locate your water meter (typically at the street curb in a covered box). Step 3: Note the meter reading and look for the leak indicator — a small dial, triangle, or star on the meter face that spins with any water movement. Step 4: Wait 15–30 minutes without using any water. Step 5: Check whether the meter reading has changed or the leak indicator is still moving. Any movement with all fixtures off indicates an active leak somewhere between the meter and the home. This test does not locate the leak — it only confirms one exists.