Leak Detection in Bonanza, Georgia

Yes. We connect Bonanza property owners and homeowners in Clayton County with licensed leak detection specialists. Our network covers all of Georgia and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Slab leak signs in Bonanza include warm or wet spots on concrete floors, a running water meter with all fixtures off, unusually high water bills, and foundation cracks appearing without an obvious cause. Clay soil movement in Clayton County stresses buried copper lines over time, making slab leaks more common in older slab-on-grade construction. Professional leak detection can confirm or rule out a slab leak without breaking your floor.

Homeowners can perform several reliable self-tests that confirm a leak exists: the water meter test (watching for movement after all fixtures are off), a toilet dye test (food coloring in the tank — if color appears in the bowl without flushing, the flapper is leaking), and visual inspection of known failure points (supply hose connections, water heater inlet/outlet, fixture supply valves). What self-tests cannot do is locate a hidden leak to a specific point. Without acoustic or tracer gas equipment, a homeowner who has confirmed via meter test that a supply leak exists cannot determine whether it is under the slab, in a wall, or in the underground service line — and an incorrect diagnosis of a slab leak location can result in unnecessary concrete cutting in the wrong spot. Professional detection is appropriate any time a self-test confirms a leak but the source is not visually obvious.

A moving meter with no visible leak almost always means the leak is hidden — either inside walls, under the slab, underground between the meter and the house, or in an irrigation system branch. The most common locations for hidden leaks detected this way are: (1) slab supply lines under the concrete floor; (2) underground service line between the meter and the house foundation; (3) toilet flappers (though these are more commonly caught by dye testing than meter observation); (4) outdoor irrigation zone valves that fail to close fully. The next diagnostic step is to isolate the leak to a specific zone by closing the main shutoff valve inside the house and observing whether the meter continues to move — if it does, the leak is between the meter and the house on the service line.

A professional slab leak detection appointment typically takes 1–3 hours on-site. The technician first performs an isolation test to confirm the leak is on the supply side (checking hot and cold lines separately) and to estimate flow rate. Acoustic detection involves placing sensors at multiple points on the floor and listening for the characteristic leak noise amplified through the concrete. In straightforward cases with good acoustic signal, the leak can be located within 60–90 minutes. Complex cases — thick slabs, multiple pipe runs, weak acoustic signal from PEX pipe — may require tracer gas as a secondary method, extending the appointment to 2–3 hours.

Professional slab leak detection typically costs $150–$400 for the detection service alone, separate from any repair work. Acoustic electronic detection — the most common method — falls in the $150–$300 range. Tracer gas detection, used when acoustic signals are weak (such as under thick concrete or with PEX pipe), typically runs $250–$400. The detection fee covers locating and marking the leak position to within a few inches, which directly reduces repair excavation costs. Detection cost is a small fraction of total project cost — avoiding unnecessary concrete cutting by knowing the exact leak location typically saves $500–$2,000 in repair labor.

Yes — most significant leaks are invisible at their source until substantial damage has occurred. Slab leaks are entirely under concrete. Underground service line leaks may not surface for months if the soil has good absorption capacity. Wall leaks from pinhole copper or failed shower pan liners discharge into wall cavities and subfloors, appearing only as staining, bubbling paint, or soft flooring. Leaks in unconditioned attic spaces may not manifest inside the living space until roof deck damage causes secondary intrusion. The absence of visible water is the primary reason leak detection technology exists — the purpose of acoustic, tracer gas, and thermal tools is to locate leaks that cannot be found by looking. An unexplained increase in water consumption confirmed by comparing monthly bills to the same period in prior years is often the only early indicator.

The most reliable early indicators are: (1) a water meter that continues to move after all fixtures are turned off — the meter test is the first self-check every homeowner should perform; (2) unexplained increases in your water bill without a change in usage; (3) warm or hot spots on floor surfaces (for hot water line leaks); (4) the sound of running water when no fixture is in use; (5) cracks appearing in interior walls or floor tiles, particularly in a linear pattern following a pipe run. Slab leaks from drain lines may not show water meter movement — instead they present as soft spots in flooring, musty odors, or unexplained moisture at baseboards. A professional acoustic or tracer gas test is needed to pinpoint the exact leak location before any repair.

Water leaks produce secondary odors rather than a direct smell from the water itself. The characteristic musty, earthy odor associated with leaks comes from mold and mildew growth in saturated building materials — typically within 24–72 hours of initial saturation in warm, humid conditions. A more specific sulfurous or sewage odor indicates a drain or sewer leak rather than a supply line leak. In wall or subfloor cavities, the smell of wet wood combined with mold is distinctive — an 'old house' smell concentrated in a specific area often points to an active hidden leak in that zone. Gas lines have an added odorant (mercaptan) that produces a distinct sulfur/rotten egg smell — this is an emergency requiring immediate evacuation and utility contact, not a plumber.

A pinhole slab leak under 40–60 PSI system pressure loses approximately 10–30 gallons per hour — or 240–720 gallons per day. A larger failure point at a pipe fitting or elbow can lose significantly more. At the national average water rate of approximately $0.006 per gallon, a mid-range slab leak costs roughly $500–$1,500 per month in wasted water before detection. Beyond water cost, this volume continuously saturates sub-slab soil, which is the mechanism for the foundation damage and mold risk that accompany long-standing undetected leaks.