Leak Detection in Lexington, Virginia

Yes. We connect Lexington property owners and homeowners in Lexington County with licensed leak detection specialists. Our network covers all of Virginia and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Elevated water pressure in Lexington accelerates wear on supply line fittings, appliance connections, and fixture valves. Lexington County municipal systems can deliver pressure above 80 PSI — above the recommended residential range of 40–60 PSI. High-pressure systems increase the risk of pinhole leaks, fitting failures, and appliance line ruptures. If your water bill is unexpectedly high, a pressure-related hidden leak is a common cause.

Pipe freeze prevention depends on your home's construction type and local frost depth. For all homes: (1) Know where your main shutoff valve is and confirm it operates before winter; (2) Disconnect and drain garden hoses from exterior hose bibs — a connected hose traps water in the spigot and can freeze back into the supply line; (3) Insulate pipes in unheated spaces — garages, crawlspaces, and unconditioned attics. For homes in regions with frost depths below 15 inches (most of the South): (4) Let faucets drip slightly during freeze events — moving water is harder to freeze; (5) Open cabinet doors under sinks on exterior walls to allow heated room air to reach the pipes. For crawlspace homes: (6) Seal crawlspace vents before first freeze to trap ground warmth. For vacant properties: (7) Maintain minimum 55°F interior temperature or fully drain and blow out the supply system with compressed air.

Responsibility is typically split at the water meter, which sits at or near the property line. The municipal water utility owns and maintains everything from the water main in the street to the meter. The homeowner owns and is responsible for everything from the meter to the house — including the full underground service line run across the property. This is an important distinction because service line leaks on the homeowner's side are the homeowner's financial responsibility, and standard homeowners insurance (HO-3 policies) does not cover underground service line repair by default. A service line insurance endorsement — available from most insurers for $30–$60 per year — extends coverage to this exposure. Some utilities have begun offering service line protection programs as a billing add-on.

Underground service line leaks are among the most expensive and least obvious leaks to identify. Signs include: (1) the water meter test shows movement with all interior fixtures off, but closing the main shutoff inside the house (which leaves only the underground service line pressurized) still shows meter movement — this isolates the leak to the underground run; (2) wet or unusually green patches in the yard that persist regardless of irrigation or rainfall; (3) a sinkhole or soft depression in the yard or driveway; (4) reduced water pressure throughout the house without an identifiable interior cause; (5) water seeping up through cracks in a driveway or sidewalk above where the service line is buried. Professional detection uses acoustic listening rods placed on the pipe at the meter and at the house entry point, or tracer gas introduced into the isolated line.

Our referral network connects property owners with leak detection specialists by location. Use the service finder to enter your city and select the type of leak concern — slab, underground, pool, sewer, or general inspection. Matching specialists in your area are returned with their service coverage areas. We recommend requesting a written detection report from any specialist before authorizing repair work — a report documenting the leak location and characteristics is valuable both for repair guidance and for insurance documentation.

A pressure reducing valve (PRV) is installed on the main water supply line entering the home to regulate incoming municipal water pressure down to a safe residential range (typically 60–80 PSI). Without a PRV, homes in high-pressure service zones (hillside neighborhoods, pump-boosted areas) can experience pressures of 100–150 PSI — far above what residential plumbing is designed for. PRV failure is a primary cause of pinhole leaks, appliance hose failures, and fixture seal failures. Signs of PRV failure: water pressure that feels excessively forceful, banging pipes (water hammer), repeatedly failing appliance supply hoses, or a water pressure gauge reading above 80 PSI. PRVs have a typical service life of 10–15 years and should be replaced proactively. Homes without a PRV in a high-pressure zone should have one installed — the cost is $250–$500 installed and can prevent thousands in damage.

Tank-style water heaters have an average service life of 8–12 years. Tankless (on-demand) water heaters last 15–20 years with proper maintenance. Factors that shorten tank heater life: high mineral content water (hard water) accelerates scale buildup on heating elements and sediment accumulation; high pressure (above 80 PSI) stresses the tank; failure to flush the tank annually allows sediment accumulation that insulates the heating element and causes overheating. The anode rod — a magnesium or aluminum rod designed to corrode sacrificially to protect the tank lining — should be inspected every 3–5 years and replaced when depleted. A depleted anode rod is the most common cause of premature tank failure. Water heaters that are more than 10 years old and showing any signs of corrosion, discolored water, or unusual noise should be proactively replaced before a catastrophic tank rupture.

Water leaks produce secondary odors rather than a direct smell from the water itself. The characteristic musty, earthy odor associated with leaks comes from mold and mildew growth in saturated building materials — typically within 24–72 hours of initial saturation in warm, humid conditions. A more specific sulfurous or sewage odor indicates a drain or sewer leak rather than a supply line leak. In wall or subfloor cavities, the smell of wet wood combined with mold is distinctive — an 'old house' smell concentrated in a specific area often points to an active hidden leak in that zone. Gas lines have an added odorant (mercaptan) that produces a distinct sulfur/rotten egg smell — this is an emergency requiring immediate evacuation and utility contact, not a plumber.

A moving meter with no visible leak almost always means the leak is hidden — either inside walls, under the slab, underground between the meter and the house, or in an irrigation system branch. The most common locations for hidden leaks detected this way are: (1) slab supply lines under the concrete floor; (2) underground service line between the meter and the house foundation; (3) toilet flappers (though these are more commonly caught by dye testing than meter observation); (4) outdoor irrigation zone valves that fail to close fully. The next diagnostic step is to isolate the leak to a specific zone by closing the main shutoff valve inside the house and observing whether the meter continues to move — if it does, the leak is between the meter and the house on the service line.