Leak Detection in Bountiful, Utah

Yes. We connect Bountiful property owners and homeowners in Davis County with licensed leak detection specialists. Our network covers all of Utah and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Elevated water pressure in Bountiful accelerates wear on supply line fittings, appliance connections, and fixture valves. Davis County municipal systems can deliver pressure above 80 PSI — above the recommended residential range of 40–60 PSI. High-pressure systems increase the risk of pinhole leaks, fitting failures, and appliance line ruptures. If your water bill is unexpectedly high, a pressure-related hidden leak is a common cause.

Underground service line leaks are among the most expensive and least obvious leaks to identify. Signs include: (1) the water meter test shows movement with all interior fixtures off, but closing the main shutoff inside the house (which leaves only the underground service line pressurized) still shows meter movement — this isolates the leak to the underground run; (2) wet or unusually green patches in the yard that persist regardless of irrigation or rainfall; (3) a sinkhole or soft depression in the yard or driveway; (4) reduced water pressure throughout the house without an identifiable interior cause; (5) water seeping up through cracks in a driveway or sidewalk above where the service line is buried. Professional detection uses acoustic listening rods placed on the pipe at the meter and at the house entry point, or tracer gas introduced into the isolated line.

Commercial leak detection differs from residential in scale, system complexity, and financial exposure. Key differences: (1) Multiple supply zones — commercial buildings often have multiple floors, zones, and dedicated risers that require systematic zone isolation before locating a leak; (2) Shared utility metering — many commercial buildings have a single master meter, making individual unit leak identification require sub-metering or zone isolation valves; (3) Higher pipe complexity — fire suppression systems, chilled water lines, steam lines, and condenser water loops add leak exposure beyond domestic water; (4) Business interruption — a commercial leak may require closing a tenant space during repair, adding business interruption cost to the property damage; (5) Landlord-tenant responsibility — lease agreements determine who bears the cost of leak detection and repair, and terms vary widely; (6) Insurance considerations — commercial property insurance has different sublimits and deductibles than residential, and business interruption coverage adds a separate coverage layer.

The Uniform Plumbing Code and International Plumbing Code both specify a maximum service pressure of 80 PSI for residential supply systems. Most appliance manufacturers void warranties on washing machine hoses, refrigerator water lines, and water heater supply valves at pressures above 80 PSI. Dishwasher fill valves and toilet fill valves are similarly rated for 80 PSI maximum. The optimal range for residential plumbing is 50–70 PSI — sufficient for good shower pressure and appliance performance while keeping stress on fittings and fixtures within safe limits. Below 40 PSI, shower performance degrades and some appliances may not fill correctly. Testing water pressure requires a simple gauge threaded onto a hose bib — available for under $15 at any home improvement store.

A sewer camera inspection uses a waterproof camera mounted on a flexible rod to visually inspect the interior of drain and sewer lines. It can identify: (1) root intrusion — tree and shrub roots entering pipe joints, which is the most common cause of sewer line failure; (2) pipe offset or separation at joints from soil settlement; (3) cracks, holes, or completely collapsed sections; (4) grease accumulation or debris blockages; (5) Orangeburg pipe deformation; (6) bellying — sections of pipe that have sagged and create standing water pools that trap solids. The camera records video with a distance marker so the technician can report the exact depth and distance of any defect for excavation planning. Most inspections also include a locator signal from the camera head so the position can be marked at the surface.

Tracer gas detection introduces a non-toxic, non-flammable gas mixture (95% nitrogen / 5% hydrogen) into the water pipe system after water is drained. The gas molecules are extremely small — smaller than water molecules — and escape through the breach point and permeate up through soil and concrete. A technician sweeps the floor surface with a calibrated hydrogen sensor that detects even trace concentrations of the tracer gas. A peak reading identifies the leak location. The 5% hydrogen mixture is specifically chosen because it is below the flammability threshold (hydrogen requires 4–75% concentration in air to ignite), making it completely safe. Tracer gas detection works on any pipe material, making it the preferred method when acoustic detection cannot produce a clear signal — particularly with PEX pipe or when the leak is very small.

Polybutylene pipe is identifiable by its gray, blue, or black color — gray is most common for interior supply lines. Look under sinks, behind the water heater, and at the point where pipes enter walls. The pipe is typically 1/2 inch or 3/4 inch diameter with a dull, matte surface. Fittings are usually gray or white plastic (acetal) or aluminum. If your home was built between 1978 and 1995 and you see gray plastic supply lines, it is almost certainly polybutylene. You can also check the pipe labeling — polybutylene is often stamped 'PB2110'. If confirmed, consult with a licensed plumber about your replacement options — polybutylene was the subject of a class action settlement (Cox v. Shell Oil) specifically because of its documented failure rate.

Thermal imaging cameras detect temperature differences on surfaces — they do not directly see water or pipes. Their value in leak detection comes from the thermal anomalies that active leaks create: (1) a hot water line leak behind a wall creates a warm zone visible as a bright spot on a thermal image; (2) a cold water leak creates a cool evaporative zone as moisture evaporates; (3) saturated insulation retains temperature differently than dry insulation, creating visible boundaries. Thermal imaging is particularly effective for: ceiling leaks from above (roof or plumbing), radiant floor heating system breaches, and locating the extent of moisture intrusion in walls after a known leak. Limitations: thermal imaging cannot locate leaks behind thick concrete slabs or deep underground, and it requires a temperature differential to be effective — in moderate temperatures, the signal may be too weak.

Ground penetrating radar (GPR) sends electromagnetic pulses into the ground and measures the reflected signals from density changes in subsurface materials. In leak detection, it serves two specific uses: (1) locating buried pipe runs before excavation — GPR can map the horizontal position and depth of underground pipes, helping technicians excavate precisely; (2) detecting voids or soil saturation anomalies that indicate long-standing leaks — water-saturated soil has a different electromagnetic signature than dry soil, allowing GPR to identify leak-affected zones even when the exact pipe location is unknown. GPR is typically used as a supplementary tool alongside acoustic or tracer gas detection, not as a standalone leak detection method.