Leak Detection in Lexington, South Carolina

Yes. We connect Lexington property owners and homeowners in Lexington County with licensed leak detection specialists. Our network covers all of South Carolina and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Slab leak signs in Lexington include warm or wet spots on concrete floors, a running water meter with all fixtures off, unusually high water bills, and foundation cracks appearing without an obvious cause. Clay soil movement in Lexington County stresses buried copper lines over time, making slab leaks more common in older slab-on-grade construction. Professional leak detection can confirm or rule out a slab leak without breaking your floor.

Polybutylene pipe is identifiable by its gray, blue, or black color — gray is most common for interior supply lines. Look under sinks, behind the water heater, and at the point where pipes enter walls. The pipe is typically 1/2 inch or 3/4 inch diameter with a dull, matte surface. Fittings are usually gray or white plastic (acetal) or aluminum. If your home was built between 1978 and 1995 and you see gray plastic supply lines, it is almost certainly polybutylene. You can also check the pipe labeling — polybutylene is often stamped 'PB2110'. If confirmed, consult with a licensed plumber about your replacement options — polybutylene was the subject of a class action settlement (Cox v. Shell Oil) specifically because of its documented failure rate.

Pipe freeze prevention depends on your home's construction type and local frost depth. For all homes: (1) Know where your main shutoff valve is and confirm it operates before winter; (2) Disconnect and drain garden hoses from exterior hose bibs — a connected hose traps water in the spigot and can freeze back into the supply line; (3) Insulate pipes in unheated spaces — garages, crawlspaces, and unconditioned attics. For homes in regions with frost depths below 15 inches (most of the South): (4) Let faucets drip slightly during freeze events — moving water is harder to freeze; (5) Open cabinet doors under sinks on exterior walls to allow heated room air to reach the pipes. For crawlspace homes: (6) Seal crawlspace vents before first freeze to trap ground warmth. For vacant properties: (7) Maintain minimum 55°F interior temperature or fully drain and blow out the supply system with compressed air.

Private service line failures (the homeowner's underground water line) are caused by: (1) pipe material age — galvanized steel and lead service lines installed in homes before 1960 are past designed service life; (2) soil movement — freeze-thaw cycling and expansive clay movement stress pipe joints repeatedly until failure; (3) tree root intrusion — roots follow moisture and can encircle and crush or pierce service lines, particularly older clay or galvanized lines; (4) external loading — heavy vehicles driving over a shallow-buried service line, or settlement of pavement above it; (5) electrolytic corrosion — stray electrical currents in the soil accelerate corrosion of metallic pipes. Plastic pipes (PVC, PEX) are significantly more resistant to all of these failure modes than older metallic pipe materials.

The water meter test is a reliable first step any homeowner can perform without tools. Step 1: Turn off all water fixtures inside and outside the home — including dishwashers, ice makers, and irrigation systems. Step 2: Locate your water meter (typically at the street curb in a covered box). Step 3: Note the meter reading and look for the leak indicator — a small dial, triangle, or star on the meter face that spins with any water movement. Step 4: Wait 15–30 minutes without using any water. Step 5: Check whether the meter reading has changed or the leak indicator is still moving. Any movement with all fixtures off indicates an active leak somewhere between the meter and the home. This test does not locate the leak — it only confirms one exists.

A professional slab leak detection appointment typically takes 1–3 hours on-site. The technician first performs an isolation test to confirm the leak is on the supply side (checking hot and cold lines separately) and to estimate flow rate. Acoustic detection involves placing sensors at multiple points on the floor and listening for the characteristic leak noise amplified through the concrete. In straightforward cases with good acoustic signal, the leak can be located within 60–90 minutes. Complex cases — thick slabs, multiple pipe runs, weak acoustic signal from PEX pipe — may require tracer gas as a secondary method, extending the appointment to 2–3 hours.

The most reliable early indicators are: (1) a water meter that continues to move after all fixtures are turned off — the meter test is the first self-check every homeowner should perform; (2) unexplained increases in your water bill without a change in usage; (3) warm or hot spots on floor surfaces (for hot water line leaks); (4) the sound of running water when no fixture is in use; (5) cracks appearing in interior walls or floor tiles, particularly in a linear pattern following a pipe run. Slab leaks from drain lines may not show water meter movement — instead they present as soft spots in flooring, musty odors, or unexplained moisture at baseboards. A professional acoustic or tracer gas test is needed to pinpoint the exact leak location before any repair.

PEX (cross-linked polyethylene) and copper are the two most common residential supply pipe materials used today. Key differences: (1) Flexibility — PEX is semi-rigid and can be routed around corners without fittings, reducing leak point count; copper is rigid and requires fittings at every bend, each of which is a potential failure point. (2) Freeze resistance — PEX expands under freezing and returns to shape on thaw, dramatically reducing freeze burst risk; copper does not expand and bursts when water freezes inside. (3) Corrosion resistance — PEX is immune to the electrochemical corrosion that causes copper pinholes; copper is susceptible to water chemistry attack. (4) Cost — PEX material is typically 25–40% cheaper than copper. (5) Lifespan — PEX has a projected 50+ year service life with limited field data beyond 25 years; copper has a demonstrated 50–70 year track record. (6) Heat tolerance — copper handles high-temperature water better; PEX has a maximum service temperature of 200°F.

Texas has the highest rate of residential slab leak detection calls of any US state, driven by a specific combination of factors: (1) Soil — the Texas Blackland Prairie and Gulf Coast Prairies sit on Vertisol clay soils with Plasticity Index values of 40–65, among the highest shrink-swell potential soils in the world. These soils undergo 3–6 inches of vertical movement per year between wet and dry seasons. (2) Construction — approximately 95% of Texas homes are built on slab foundations directly in contact with this soil, placing copper supply pipes in direct contact with soil that is constantly moving. (3) Climate — Texas experiences extended summer droughts that maximize soil desiccation and movement, followed by heavy rainfall that causes rapid re-expansion. (4) Pipe era — the bulk of the Texas housing stock was built between 1960 and 1990 with copper supply pipe that now has 30–60 years of service on highly mobile soil.