Leak Detection in Myrtle Beach, South Carolina

Yes. We connect Myrtle Beach property owners and homeowners in Horry County with licensed leak detection specialists. Our network covers all of South Carolina and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Slab leak signs in Myrtle Beach include warm or wet spots on concrete floors, a running water meter with all fixtures off, unusually high water bills, and foundation cracks appearing without an obvious cause. Clay soil movement in Horry County stresses buried copper lines over time, making slab leaks more common in older slab-on-grade construction. Professional leak detection can confirm or rule out a slab leak without breaking your floor.

Professional slab leak detection typically costs $150–$400 for the detection service alone, separate from any repair work. Acoustic electronic detection — the most common method — falls in the $150–$300 range. Tracer gas detection, used when acoustic signals are weak (such as under thick concrete or with PEX pipe), typically runs $250–$400. The detection fee covers locating and marking the leak position to within a few inches, which directly reduces repair excavation costs. Detection cost is a small fraction of total project cost — avoiding unnecessary concrete cutting by knowing the exact leak location typically saves $500–$2,000 in repair labor.

Underground service line leaks are among the most expensive and least obvious leaks to identify. Signs include: (1) the water meter test shows movement with all interior fixtures off, but closing the main shutoff inside the house (which leaves only the underground service line pressurized) still shows meter movement — this isolates the leak to the underground run; (2) wet or unusually green patches in the yard that persist regardless of irrigation or rainfall; (3) a sinkhole or soft depression in the yard or driveway; (4) reduced water pressure throughout the house without an identifiable interior cause; (5) water seeping up through cracks in a driveway or sidewalk above where the service line is buried. Professional detection uses acoustic listening rods placed on the pipe at the meter and at the house entry point, or tracer gas introduced into the isolated line.

Yes — and this is a frequently overlooked risk. An in-ground pool that develops a structural leak can introduce hundreds of gallons per day into the surrounding soil. In expansive clay soils, this causes chronic soil saturation that keeps the clay in a swollen state — which can destabilize adjacent foundation footings and slabs. In sandy or permeable soils, continuous pool leak flow can wash soil away from beneath adjacent structures, causing settlement. Pool leaks typically go undiagnosed because pool owners attribute water loss to evaporation — but evaporation rarely exceeds 1/4 inch per day, while pool leaks can exceed 1 inch per day. The bucket test (floating a bucket of water in the pool for 24 hours and comparing the drop in pool level to the drop in bucket level) is the standard homeowner self-test for pool leak identification.

Yes — and this is the primary reason early detection matters. A pressurized supply line leak under a slab introduces water into the sub-slab soil at a continuous rate. In expansive clay soils, this causes localized soil swelling that can heave the slab unevenly. In sandy or silty soils, it can cause subsidence — the opposite problem, where the soil washes away and the slab loses support. Either scenario produces differential foundation movement, which manifests as sticking doors, diagonal wall cracks, and sloping floors. Foundation damage from an undetected slab leak is typically not covered by standard homeowners insurance as it is classified as ongoing neglect rather than a sudden event.

Polybutylene pipe is identifiable by its gray, blue, or black color — gray is most common for interior supply lines. Look under sinks, behind the water heater, and at the point where pipes enter walls. The pipe is typically 1/2 inch or 3/4 inch diameter with a dull, matte surface. Fittings are usually gray or white plastic (acetal) or aluminum. If your home was built between 1978 and 1995 and you see gray plastic supply lines, it is almost certainly polybutylene. You can also check the pipe labeling — polybutylene is often stamped 'PB2110'. If confirmed, consult with a licensed plumber about your replacement options — polybutylene was the subject of a class action settlement (Cox v. Shell Oil) specifically because of its documented failure rate.

Water leaks produce secondary odors rather than a direct smell from the water itself. The characteristic musty, earthy odor associated with leaks comes from mold and mildew growth in saturated building materials — typically within 24–72 hours of initial saturation in warm, humid conditions. A more specific sulfurous or sewage odor indicates a drain or sewer leak rather than a supply line leak. In wall or subfloor cavities, the smell of wet wood combined with mold is distinctive — an 'old house' smell concentrated in a specific area often points to an active hidden leak in that zone. Gas lines have an added odorant (mercaptan) that produces a distinct sulfur/rotten egg smell — this is an emergency requiring immediate evacuation and utility contact, not a plumber.

Orangeburg pipe (also called bituminous fiber pipe) is a drain and sewer pipe made from layers of wood pulp and pitch, manufactured from the 1860s through the 1970s. It was widely used as drain and sewer pipe in homes built before 1970 because it was inexpensive and easy to cut. The problem: Orangeburg was designed with an expected service life of 50 years, and that life is now long expired. It absorbs moisture over time, which causes it to deform from a round cross-section to an oval or collapsed shape. Once deformed, it can no longer carry sewage effectively, and complete collapse follows. Homes built before 1970 — particularly in the Northeast and Midwest — have a high probability of having Orangeburg sewer laterals. A sewer camera inspection is the definitive test.

PEX (cross-linked polyethylene) and copper are the two most common residential supply pipe materials used today. Key differences: (1) Flexibility — PEX is semi-rigid and can be routed around corners without fittings, reducing leak point count; copper is rigid and requires fittings at every bend, each of which is a potential failure point. (2) Freeze resistance — PEX expands under freezing and returns to shape on thaw, dramatically reducing freeze burst risk; copper does not expand and bursts when water freezes inside. (3) Corrosion resistance — PEX is immune to the electrochemical corrosion that causes copper pinholes; copper is susceptible to water chemistry attack. (4) Cost — PEX material is typically 25–40% cheaper than copper. (5) Lifespan — PEX has a projected 50+ year service life with limited field data beyond 25 years; copper has a demonstrated 50–70 year track record. (6) Heat tolerance — copper handles high-temperature water better; PEX has a maximum service temperature of 200°F.