Leak Detection in Cayce, South Carolina

Yes. We connect Cayce property owners and homeowners in Lexington County with licensed leak detection specialists. Our network covers all of South Carolina and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Slab leak signs in Cayce include warm or wet spots on concrete floors, a running water meter with all fixtures off, unusually high water bills, and foundation cracks appearing without an obvious cause. Clay soil movement in Lexington County stresses buried copper lines over time, making slab leaks more common in older slab-on-grade construction. Professional leak detection can confirm or rule out a slab leak without breaking your floor.

Polybutylene pipe is identifiable by its gray, blue, or black color — gray is most common for interior supply lines. Look under sinks, behind the water heater, and at the point where pipes enter walls. The pipe is typically 1/2 inch or 3/4 inch diameter with a dull, matte surface. Fittings are usually gray or white plastic (acetal) or aluminum. If your home was built between 1978 and 1995 and you see gray plastic supply lines, it is almost certainly polybutylene. You can also check the pipe labeling — polybutylene is often stamped 'PB2110'. If confirmed, consult with a licensed plumber about your replacement options — polybutylene was the subject of a class action settlement (Cox v. Shell Oil) specifically because of its documented failure rate.

Pipe freeze prevention depends on your home's construction type and local frost depth. For all homes: (1) Know where your main shutoff valve is and confirm it operates before winter; (2) Disconnect and drain garden hoses from exterior hose bibs — a connected hose traps water in the spigot and can freeze back into the supply line; (3) Insulate pipes in unheated spaces — garages, crawlspaces, and unconditioned attics. For homes in regions with frost depths below 15 inches (most of the South): (4) Let faucets drip slightly during freeze events — moving water is harder to freeze; (5) Open cabinet doors under sinks on exterior walls to allow heated room air to reach the pipes. For crawlspace homes: (6) Seal crawlspace vents before first freeze to trap ground warmth. For vacant properties: (7) Maintain minimum 55°F interior temperature or fully drain and blow out the supply system with compressed air.

PEX (cross-linked polyethylene) and copper are the two most common residential supply pipe materials used today. Key differences: (1) Flexibility — PEX is semi-rigid and can be routed around corners without fittings, reducing leak point count; copper is rigid and requires fittings at every bend, each of which is a potential failure point. (2) Freeze resistance — PEX expands under freezing and returns to shape on thaw, dramatically reducing freeze burst risk; copper does not expand and bursts when water freezes inside. (3) Corrosion resistance — PEX is immune to the electrochemical corrosion that causes copper pinholes; copper is susceptible to water chemistry attack. (4) Cost — PEX material is typically 25–40% cheaper than copper. (5) Lifespan — PEX has a projected 50+ year service life with limited field data beyond 25 years; copper has a demonstrated 50–70 year track record. (6) Heat tolerance — copper handles high-temperature water better; PEX has a maximum service temperature of 200°F.

A moving meter with no visible leak almost always means the leak is hidden — either inside walls, under the slab, underground between the meter and the house, or in an irrigation system branch. The most common locations for hidden leaks detected this way are: (1) slab supply lines under the concrete floor; (2) underground service line between the meter and the house foundation; (3) toilet flappers (though these are more commonly caught by dye testing than meter observation); (4) outdoor irrigation zone valves that fail to close fully. The next diagnostic step is to isolate the leak to a specific zone by closing the main shutoff valve inside the house and observing whether the meter continues to move — if it does, the leak is between the meter and the house on the service line.

Texas has the highest rate of residential slab leak detection calls of any US state, driven by a specific combination of factors: (1) Soil — the Texas Blackland Prairie and Gulf Coast Prairies sit on Vertisol clay soils with Plasticity Index values of 40–65, among the highest shrink-swell potential soils in the world. These soils undergo 3–6 inches of vertical movement per year between wet and dry seasons. (2) Construction — approximately 95% of Texas homes are built on slab foundations directly in contact with this soil, placing copper supply pipes in direct contact with soil that is constantly moving. (3) Climate — Texas experiences extended summer droughts that maximize soil desiccation and movement, followed by heavy rainfall that causes rapid re-expansion. (4) Pipe era — the bulk of the Texas housing stock was built between 1960 and 1990 with copper supply pipe that now has 30–60 years of service on highly mobile soil.

Professional slab leak detection typically costs $150–$400 for the detection service alone, separate from any repair work. Acoustic electronic detection — the most common method — falls in the $150–$300 range. Tracer gas detection, used when acoustic signals are weak (such as under thick concrete or with PEX pipe), typically runs $250–$400. The detection fee covers locating and marking the leak position to within a few inches, which directly reduces repair excavation costs. Detection cost is a small fraction of total project cost — avoiding unnecessary concrete cutting by knowing the exact leak location typically saves $500–$2,000 in repair labor.

Yes — and this is the primary reason early detection matters. A pressurized supply line leak under a slab introduces water into the sub-slab soil at a continuous rate. In expansive clay soils, this causes localized soil swelling that can heave the slab unevenly. In sandy or silty soils, it can cause subsidence — the opposite problem, where the soil washes away and the slab loses support. Either scenario produces differential foundation movement, which manifests as sticking doors, diagonal wall cracks, and sloping floors. Foundation damage from an undetected slab leak is typically not covered by standard homeowners insurance as it is classified as ongoing neglect rather than a sudden event.

A pinhole slab leak under 40–60 PSI system pressure loses approximately 10–30 gallons per hour — or 240–720 gallons per day. A larger failure point at a pipe fitting or elbow can lose significantly more. At the national average water rate of approximately $0.006 per gallon, a mid-range slab leak costs roughly $500–$1,500 per month in wasted water before detection. Beyond water cost, this volume continuously saturates sub-slab soil, which is the mechanism for the foundation damage and mold risk that accompany long-standing undetected leaks.