Leak Detection in Mount Pleasant, South Carolina

Yes. We connect Mount Pleasant property owners and homeowners in Charleston County with licensed leak detection specialists. Our network covers all of South Carolina and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Slab leak signs in Mount Pleasant include warm or wet spots on concrete floors, a running water meter with all fixtures off, unusually high water bills, and foundation cracks appearing without an obvious cause. Clay soil movement in Charleston County stresses buried copper lines over time, making slab leaks more common in older slab-on-grade construction. Professional leak detection can confirm or rule out a slab leak without breaking your floor.

Galvanized pipes are not immediately dangerous in the way a gas leak is — they present a gradual risk that worsens over time. Galvanized steel pipe corrodes from the inside out. As zinc coating dissolves (typically after 40–50 years), rust accumulates on pipe walls, progressively reducing water flow, discoloring water, and ultimately causing pinhole failures or joint failures. The primary risks are: (1) water quality — orange or rust-colored water from galvanized pipes is a documented health concern as the rust can harbor bacteria and introduces iron above EPA aesthetic limits; (2) reduced flow — heavy rust buildup can reduce pipe diameter by 50–70% in severely corroded runs; (3) lead contamination risk — galvanized pipe used downstream of lead service lines can adsorb and release lead, a documented issue in cities with older municipal infrastructure. Homes with galvanized supply lines more than 50 years old should have them evaluated for replacement.

The most reliable early indicators are: (1) a water meter that continues to move after all fixtures are turned off — the meter test is the first self-check every homeowner should perform; (2) unexplained increases in your water bill without a change in usage; (3) warm or hot spots on floor surfaces (for hot water line leaks); (4) the sound of running water when no fixture is in use; (5) cracks appearing in interior walls or floor tiles, particularly in a linear pattern following a pipe run. Slab leaks from drain lines may not show water meter movement — instead they present as soft spots in flooring, musty odors, or unexplained moisture at baseboards. A professional acoustic or tracer gas test is needed to pinpoint the exact leak location before any repair.

A moving meter with no visible leak almost always means the leak is hidden — either inside walls, under the slab, underground between the meter and the house, or in an irrigation system branch. The most common locations for hidden leaks detected this way are: (1) slab supply lines under the concrete floor; (2) underground service line between the meter and the house foundation; (3) toilet flappers (though these are more commonly caught by dye testing than meter observation); (4) outdoor irrigation zone valves that fail to close fully. The next diagnostic step is to isolate the leak to a specific zone by closing the main shutoff valve inside the house and observing whether the meter continues to move — if it does, the leak is between the meter and the house on the service line.

Polybutylene pipe is identifiable by its gray, blue, or black color — gray is most common for interior supply lines. Look under sinks, behind the water heater, and at the point where pipes enter walls. The pipe is typically 1/2 inch or 3/4 inch diameter with a dull, matte surface. Fittings are usually gray or white plastic (acetal) or aluminum. If your home was built between 1978 and 1995 and you see gray plastic supply lines, it is almost certainly polybutylene. You can also check the pipe labeling — polybutylene is often stamped 'PB2110'. If confirmed, consult with a licensed plumber about your replacement options — polybutylene was the subject of a class action settlement (Cox v. Shell Oil) specifically because of its documented failure rate.

Water leaks produce secondary odors rather than a direct smell from the water itself. The characteristic musty, earthy odor associated with leaks comes from mold and mildew growth in saturated building materials — typically within 24–72 hours of initial saturation in warm, humid conditions. A more specific sulfurous or sewage odor indicates a drain or sewer leak rather than a supply line leak. In wall or subfloor cavities, the smell of wet wood combined with mold is distinctive — an 'old house' smell concentrated in a specific area often points to an active hidden leak in that zone. Gas lines have an added odorant (mercaptan) that produces a distinct sulfur/rotten egg smell — this is an emergency requiring immediate evacuation and utility contact, not a plumber.

PEX (cross-linked polyethylene) and copper are the two most common residential supply pipe materials used today. Key differences: (1) Flexibility — PEX is semi-rigid and can be routed around corners without fittings, reducing leak point count; copper is rigid and requires fittings at every bend, each of which is a potential failure point. (2) Freeze resistance — PEX expands under freezing and returns to shape on thaw, dramatically reducing freeze burst risk; copper does not expand and bursts when water freezes inside. (3) Corrosion resistance — PEX is immune to the electrochemical corrosion that causes copper pinholes; copper is susceptible to water chemistry attack. (4) Cost — PEX material is typically 25–40% cheaper than copper. (5) Lifespan — PEX has a projected 50+ year service life with limited field data beyond 25 years; copper has a demonstrated 50–70 year track record. (6) Heat tolerance — copper handles high-temperature water better; PEX has a maximum service temperature of 200°F.

Yes — and this is a frequently overlooked risk. An in-ground pool that develops a structural leak can introduce hundreds of gallons per day into the surrounding soil. In expansive clay soils, this causes chronic soil saturation that keeps the clay in a swollen state — which can destabilize adjacent foundation footings and slabs. In sandy or permeable soils, continuous pool leak flow can wash soil away from beneath adjacent structures, causing settlement. Pool leaks typically go undiagnosed because pool owners attribute water loss to evaporation — but evaporation rarely exceeds 1/4 inch per day, while pool leaks can exceed 1 inch per day. The bucket test (floating a bucket of water in the pool for 24 hours and comparing the drop in pool level to the drop in bucket level) is the standard homeowner self-test for pool leak identification.

Tree roots are a primary cause of sewer and drain line failure but rarely breach pressurized supply lines directly. The mechanism differs by line type: For drain and sewer lines — roots seek moisture and enter through pipe joints, cracks, or defects in clay tile, cast iron, concrete, or Orangeburg pipe. Once inside, they grow to fill the pipe diameter. For supply lines — roots can encircle and compress older metallic pipes over decades, causing deformation at joints. They can also cause joint separation through root growth pressure, particularly in older galvanized or lead pipe systems. For irrigation lines — roots seeking moisture are a common cause of drip emitter failure and shallow poly pipe breaches. The tree root risk radius is approximately equal to the tree's drip line (the canopy edge) for actively growing roots, but larger established root systems may extend 2–3× the drip line.