Leak Detection in Pomona, New York

Yes. We connect Pomona property owners and homeowners in Rockland County with licensed leak detection specialists. Our network covers all of New York and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

In Pomona, pipes in unheated spaces — crawlspaces, garages, exterior walls — are most vulnerable during hard freezes. A pipe that freezes may not burst immediately; freeze-thaw cycling creates micro-fractures that fail days or weeks later. If you experienced a freeze event and notice reduced pressure or unexplained moisture in Rockland County, professional leak detection can find damage before it becomes a larger structural problem.

The water meter test is a reliable first step any homeowner can perform without tools. Step 1: Turn off all water fixtures inside and outside the home — including dishwashers, ice makers, and irrigation systems. Step 2: Locate your water meter (typically at the street curb in a covered box). Step 3: Note the meter reading and look for the leak indicator — a small dial, triangle, or star on the meter face that spins with any water movement. Step 4: Wait 15–30 minutes without using any water. Step 5: Check whether the meter reading has changed or the leak indicator is still moving. Any movement with all fixtures off indicates an active leak somewhere between the meter and the home. This test does not locate the leak — it only confirms one exists.

Thermal imaging cameras detect temperature differences on surfaces — they do not directly see water or pipes. Their value in leak detection comes from the thermal anomalies that active leaks create: (1) a hot water line leak behind a wall creates a warm zone visible as a bright spot on a thermal image; (2) a cold water leak creates a cool evaporative zone as moisture evaporates; (3) saturated insulation retains temperature differently than dry insulation, creating visible boundaries. Thermal imaging is particularly effective for: ceiling leaks from above (roof or plumbing), radiant floor heating system breaches, and locating the extent of moisture intrusion in walls after a known leak. Limitations: thermal imaging cannot locate leaks behind thick concrete slabs or deep underground, and it requires a temperature differential to be effective — in moderate temperatures, the signal may be too weak.

Pipe freeze prevention depends on your home's construction type and local frost depth. For all homes: (1) Know where your main shutoff valve is and confirm it operates before winter; (2) Disconnect and drain garden hoses from exterior hose bibs — a connected hose traps water in the spigot and can freeze back into the supply line; (3) Insulate pipes in unheated spaces — garages, crawlspaces, and unconditioned attics. For homes in regions with frost depths below 15 inches (most of the South): (4) Let faucets drip slightly during freeze events — moving water is harder to freeze; (5) Open cabinet doors under sinks on exterior walls to allow heated room air to reach the pipes. For crawlspace homes: (6) Seal crawlspace vents before first freeze to trap ground warmth. For vacant properties: (7) Maintain minimum 55°F interior temperature or fully drain and blow out the supply system with compressed air.

A moving meter with no visible leak almost always means the leak is hidden — either inside walls, under the slab, underground between the meter and the house, or in an irrigation system branch. The most common locations for hidden leaks detected this way are: (1) slab supply lines under the concrete floor; (2) underground service line between the meter and the house foundation; (3) toilet flappers (though these are more commonly caught by dye testing than meter observation); (4) outdoor irrigation zone valves that fail to close fully. The next diagnostic step is to isolate the leak to a specific zone by closing the main shutoff valve inside the house and observing whether the meter continues to move — if it does, the leak is between the meter and the house on the service line.

Summer creates several distinct leak drivers that make July and August peak months for certain leak types: (1) Peak water demand — irrigation, pools, and increased usage push system pressure to seasonal highs that stress aging pipe fittings; (2) Soil desiccation — in clay soil regions, summer drought causes maximum shrinkage, creating soil movement that stresses slab-embedded and buried pipes; (3) Thermal expansion — copper supply lines experience their maximum annual thermal expansion in summer, stressing joints; (4) Irrigation system activation — irrigation systems that have been off all winter often reveal cracked heads, failed zone valves, and failed backflow preventers when restarted in spring/summer; (5) Pool and outdoor plumbing use — outdoor plumbing that is inactive in winter begins operating again, and winter-damaged fittings fail under pressure.

Water heater leaks have several distinct sources, each with different severity implications: (1) Temperature and pressure relief valve (T&P valve) — if this valve is dripping or discharging, it is responding to excessive pressure or temperature, a potentially dangerous condition requiring immediate service; (2) Drain valve — a dripping drain valve at the bottom of the tank is a minor fitting issue, typically $20–$50 to replace; (3) Supply connections — the cold water inlet and hot water outlet fittings on top of the tank develop drips from electrolytic corrosion between dissimilar metals; (4) Tank itself — a leaking tank body indicates internal corrosion has breached the tank liner, which means the heater cannot be repaired and must be replaced. The rule of thumb: any leak from connections or valves may be repairable; any leak from the tank body requires replacement.

Tank-style water heaters have an average service life of 8–12 years. Tankless (on-demand) water heaters last 15–20 years with proper maintenance. Factors that shorten tank heater life: high mineral content water (hard water) accelerates scale buildup on heating elements and sediment accumulation; high pressure (above 80 PSI) stresses the tank; failure to flush the tank annually allows sediment accumulation that insulates the heating element and causes overheating. The anode rod — a magnesium or aluminum rod designed to corrode sacrificially to protect the tank lining — should be inspected every 3–5 years and replaced when depleted. A depleted anode rod is the most common cause of premature tank failure. Water heaters that are more than 10 years old and showing any signs of corrosion, discolored water, or unusual noise should be proactively replaced before a catastrophic tank rupture.

Galvanized pipes are not immediately dangerous in the way a gas leak is — they present a gradual risk that worsens over time. Galvanized steel pipe corrodes from the inside out. As zinc coating dissolves (typically after 40–50 years), rust accumulates on pipe walls, progressively reducing water flow, discoloring water, and ultimately causing pinhole failures or joint failures. The primary risks are: (1) water quality — orange or rust-colored water from galvanized pipes is a documented health concern as the rust can harbor bacteria and introduces iron above EPA aesthetic limits; (2) reduced flow — heavy rust buildup can reduce pipe diameter by 50–70% in severely corroded runs; (3) lead contamination risk — galvanized pipe used downstream of lead service lines can adsorb and release lead, a documented issue in cities with older municipal infrastructure. Homes with galvanized supply lines more than 50 years old should have them evaluated for replacement.