Leak Detection in Point Pleasant, New Jersey

Yes. We connect Point Pleasant property owners and homeowners in Ocean County with licensed leak detection specialists. Our network covers all of New Jersey and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

In Point Pleasant, pipes in unheated spaces — crawlspaces, garages, exterior walls — are most vulnerable during hard freezes. A pipe that freezes may not burst immediately; freeze-thaw cycling creates micro-fractures that fail days or weeks later. If you experienced a freeze event and notice reduced pressure or unexplained moisture in Ocean County, professional leak detection can find damage before it becomes a larger structural problem.

Underground service line leaks are among the most expensive and least obvious leaks to identify. Signs include: (1) the water meter test shows movement with all interior fixtures off, but closing the main shutoff inside the house (which leaves only the underground service line pressurized) still shows meter movement — this isolates the leak to the underground run; (2) wet or unusually green patches in the yard that persist regardless of irrigation or rainfall; (3) a sinkhole or soft depression in the yard or driveway; (4) reduced water pressure throughout the house without an identifiable interior cause; (5) water seeping up through cracks in a driveway or sidewalk above where the service line is buried. Professional detection uses acoustic listening rods placed on the pipe at the meter and at the house entry point, or tracer gas introduced into the isolated line.

Galvanized pipes are not immediately dangerous in the way a gas leak is — they present a gradual risk that worsens over time. Galvanized steel pipe corrodes from the inside out. As zinc coating dissolves (typically after 40–50 years), rust accumulates on pipe walls, progressively reducing water flow, discoloring water, and ultimately causing pinhole failures or joint failures. The primary risks are: (1) water quality — orange or rust-colored water from galvanized pipes is a documented health concern as the rust can harbor bacteria and introduces iron above EPA aesthetic limits; (2) reduced flow — heavy rust buildup can reduce pipe diameter by 50–70% in severely corroded runs; (3) lead contamination risk — galvanized pipe used downstream of lead service lines can adsorb and release lead, a documented issue in cities with older municipal infrastructure. Homes with galvanized supply lines more than 50 years old should have them evaluated for replacement.

The water meter test is a reliable first step any homeowner can perform without tools. Step 1: Turn off all water fixtures inside and outside the home — including dishwashers, ice makers, and irrigation systems. Step 2: Locate your water meter (typically at the street curb in a covered box). Step 3: Note the meter reading and look for the leak indicator — a small dial, triangle, or star on the meter face that spins with any water movement. Step 4: Wait 15–30 minutes without using any water. Step 5: Check whether the meter reading has changed or the leak indicator is still moving. Any movement with all fixtures off indicates an active leak somewhere between the meter and the home. This test does not locate the leak — it only confirms one exists.

Polybutylene pipe is identifiable by its gray, blue, or black color — gray is most common for interior supply lines. Look under sinks, behind the water heater, and at the point where pipes enter walls. The pipe is typically 1/2 inch or 3/4 inch diameter with a dull, matte surface. Fittings are usually gray or white plastic (acetal) or aluminum. If your home was built between 1978 and 1995 and you see gray plastic supply lines, it is almost certainly polybutylene. You can also check the pipe labeling — polybutylene is often stamped 'PB2110'. If confirmed, consult with a licensed plumber about your replacement options — polybutylene was the subject of a class action settlement (Cox v. Shell Oil) specifically because of its documented failure rate.

A pinhole slab leak under 40–60 PSI system pressure loses approximately 10–30 gallons per hour — or 240–720 gallons per day. A larger failure point at a pipe fitting or elbow can lose significantly more. At the national average water rate of approximately $0.006 per gallon, a mid-range slab leak costs roughly $500–$1,500 per month in wasted water before detection. Beyond water cost, this volume continuously saturates sub-slab soil, which is the mechanism for the foundation damage and mold risk that accompany long-standing undetected leaks.

Orangeburg pipe (also called bituminous fiber pipe) is a drain and sewer pipe made from layers of wood pulp and pitch, manufactured from the 1860s through the 1970s. It was widely used as drain and sewer pipe in homes built before 1970 because it was inexpensive and easy to cut. The problem: Orangeburg was designed with an expected service life of 50 years, and that life is now long expired. It absorbs moisture over time, which causes it to deform from a round cross-section to an oval or collapsed shape. Once deformed, it can no longer carry sewage effectively, and complete collapse follows. Homes built before 1970 — particularly in the Northeast and Midwest — have a high probability of having Orangeburg sewer laterals. A sewer camera inspection is the definitive test.

Our referral network connects property owners with leak detection specialists by location. Use the service finder to enter your city and select the type of leak concern — slab, underground, pool, sewer, or general inspection. Matching specialists in your area are returned with their service coverage areas. We recommend requesting a written detection report from any specialist before authorizing repair work — a report documenting the leak location and characteristics is valuable both for repair guidance and for insurance documentation.

Homeowners can perform several reliable self-tests that confirm a leak exists: the water meter test (watching for movement after all fixtures are off), a toilet dye test (food coloring in the tank — if color appears in the bowl without flushing, the flapper is leaking), and visual inspection of known failure points (supply hose connections, water heater inlet/outlet, fixture supply valves). What self-tests cannot do is locate a hidden leak to a specific point. Without acoustic or tracer gas equipment, a homeowner who has confirmed via meter test that a supply leak exists cannot determine whether it is under the slab, in a wall, or in the underground service line — and an incorrect diagnosis of a slab leak location can result in unnecessary concrete cutting in the wrong spot. Professional detection is appropriate any time a self-test confirms a leak but the source is not visually obvious.