Leak Detection in Atco, New Jersey

Yes. We connect Atco property owners and homeowners in Camden County with licensed leak detection specialists. Our network covers all of New Jersey and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

In Atco, pipes in unheated spaces — crawlspaces, garages, exterior walls — are most vulnerable during hard freezes. A pipe that freezes may not burst immediately; freeze-thaw cycling creates micro-fractures that fail days or weeks later. If you experienced a freeze event and notice reduced pressure or unexplained moisture in Camden County, professional leak detection can find damage before it becomes a larger structural problem.

Homeowners can perform several reliable self-tests that confirm a leak exists: the water meter test (watching for movement after all fixtures are off), a toilet dye test (food coloring in the tank — if color appears in the bowl without flushing, the flapper is leaking), and visual inspection of known failure points (supply hose connections, water heater inlet/outlet, fixture supply valves). What self-tests cannot do is locate a hidden leak to a specific point. Without acoustic or tracer gas equipment, a homeowner who has confirmed via meter test that a supply leak exists cannot determine whether it is under the slab, in a wall, or in the underground service line — and an incorrect diagnosis of a slab leak location can result in unnecessary concrete cutting in the wrong spot. Professional detection is appropriate any time a self-test confirms a leak but the source is not visually obvious.

A pressure reducing valve (PRV) is installed on the main water supply line entering the home to regulate incoming municipal water pressure down to a safe residential range (typically 60–80 PSI). Without a PRV, homes in high-pressure service zones (hillside neighborhoods, pump-boosted areas) can experience pressures of 100–150 PSI — far above what residential plumbing is designed for. PRV failure is a primary cause of pinhole leaks, appliance hose failures, and fixture seal failures. Signs of PRV failure: water pressure that feels excessively forceful, banging pipes (water hammer), repeatedly failing appliance supply hoses, or a water pressure gauge reading above 80 PSI. PRVs have a typical service life of 10–15 years and should be replaced proactively. Homes without a PRV in a high-pressure zone should have one installed — the cost is $250–$500 installed and can prevent thousands in damage.

Galvanized pipes are not immediately dangerous in the way a gas leak is — they present a gradual risk that worsens over time. Galvanized steel pipe corrodes from the inside out. As zinc coating dissolves (typically after 40–50 years), rust accumulates on pipe walls, progressively reducing water flow, discoloring water, and ultimately causing pinhole failures or joint failures. The primary risks are: (1) water quality — orange or rust-colored water from galvanized pipes is a documented health concern as the rust can harbor bacteria and introduces iron above EPA aesthetic limits; (2) reduced flow — heavy rust buildup can reduce pipe diameter by 50–70% in severely corroded runs; (3) lead contamination risk — galvanized pipe used downstream of lead service lines can adsorb and release lead, a documented issue in cities with older municipal infrastructure. Homes with galvanized supply lines more than 50 years old should have them evaluated for replacement.

A pinhole slab leak under 40–60 PSI system pressure loses approximately 10–30 gallons per hour — or 240–720 gallons per day. A larger failure point at a pipe fitting or elbow can lose significantly more. At the national average water rate of approximately $0.006 per gallon, a mid-range slab leak costs roughly $500–$1,500 per month in wasted water before detection. Beyond water cost, this volume continuously saturates sub-slab soil, which is the mechanism for the foundation damage and mold risk that accompany long-standing undetected leaks.

Detection accuracy varies by method and conditions. Acoustic detection on metallic pipe in optimal conditions (quiet environment, single leak point, copper pipe) has a location accuracy of approximately ±6–12 inches — sufficient to guide surgical excavation. Tracer gas detection is generally considered the most accurate method, with location accuracy of ±3–6 inches in most conditions because the gas rises directly above the breach point. Thermal imaging accuracy for wall leaks is ±6–18 inches depending on wall composition and temperature differential. Accuracy degrades in: multi-leak scenarios (acoustic signal from secondary leaks masks primary); very small leaks below 0.5 GPM; very deep pipe runs; and thick concrete slabs (>8 inches). A professional detection report should state the location with reference measurements from fixed landmarks — not just a mark on the floor — so the location can be re-established if needed.

A moving meter with no visible leak almost always means the leak is hidden — either inside walls, under the slab, underground between the meter and the house, or in an irrigation system branch. The most common locations for hidden leaks detected this way are: (1) slab supply lines under the concrete floor; (2) underground service line between the meter and the house foundation; (3) toilet flappers (though these are more commonly caught by dye testing than meter observation); (4) outdoor irrigation zone valves that fail to close fully. The next diagnostic step is to isolate the leak to a specific zone by closing the main shutoff valve inside the house and observing whether the meter continues to move — if it does, the leak is between the meter and the house on the service line.

Underground service line leaks are among the most expensive and least obvious leaks to identify. Signs include: (1) the water meter test shows movement with all interior fixtures off, but closing the main shutoff inside the house (which leaves only the underground service line pressurized) still shows meter movement — this isolates the leak to the underground run; (2) wet or unusually green patches in the yard that persist regardless of irrigation or rainfall; (3) a sinkhole or soft depression in the yard or driveway; (4) reduced water pressure throughout the house without an identifiable interior cause; (5) water seeping up through cracks in a driveway or sidewalk above where the service line is buried. Professional detection uses acoustic listening rods placed on the pipe at the meter and at the house entry point, or tracer gas introduced into the isolated line.

Expansive soil (also called shrink-swell soil) is soil with a high clay mineral content — specifically smectite and montmorillonite clay minerals — that absorbs water and swells, then dries and contracts. The degree of movement is measured by the Plasticity Index (PI): a PI above 30 is considered high, above 40 very high. For buried and slab-embedded pipes, this movement creates: (1) bending stress as the soil moves laterally or vertically; (2) abrasion as soil particles move against the pipe exterior; (3) joint stress at fittings, which are the weakest points in any pipe run. Copper pipe is particularly vulnerable because it cannot flex to accommodate movement — even small angular deflections at joints cause micro-fracturing that propagates over years of repeated cycles. PEX pipe's flexibility makes it significantly more resistant to expansive soil damage.