Leak Detection in Shreveport, Louisiana

Yes. We connect Shreveport property owners and homeowners in Caddo County with licensed leak detection specialists. Our network covers all of Louisiana and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

Slab leak signs in Shreveport include warm or wet spots on concrete floors, a running water meter with all fixtures off, unusually high water bills, and foundation cracks appearing without an obvious cause. Clay soil movement in Caddo County stresses buried copper lines over time, making slab leaks more common in older slab-on-grade construction. Professional leak detection can confirm or rule out a slab leak without breaking your floor.

Galvanized pipes are not immediately dangerous in the way a gas leak is — they present a gradual risk that worsens over time. Galvanized steel pipe corrodes from the inside out. As zinc coating dissolves (typically after 40–50 years), rust accumulates on pipe walls, progressively reducing water flow, discoloring water, and ultimately causing pinhole failures or joint failures. The primary risks are: (1) water quality — orange or rust-colored water from galvanized pipes is a documented health concern as the rust can harbor bacteria and introduces iron above EPA aesthetic limits; (2) reduced flow — heavy rust buildup can reduce pipe diameter by 50–70% in severely corroded runs; (3) lead contamination risk — galvanized pipe used downstream of lead service lines can adsorb and release lead, a documented issue in cities with older municipal infrastructure. Homes with galvanized supply lines more than 50 years old should have them evaluated for replacement.

Slab leaks occur when a water supply or drain line embedded in a concrete foundation develops a breach. The three primary causes are: (1) soil movement — expansive clay soils shrink and swell seasonally, stressing pipe joints and bending copper lines over time; (2) pipe corrosion — copper pipes embedded in concrete are exposed to alkaline pH and mineral contact that accelerates pitting; (3) water hammer — repeated pressure surges from rapid valve closures create micro-fractures at elbows and fittings. In cities built on high-shrink-swell Vertisol clay (Houston, Dallas, the Texas Blackland Prairie), soil movement is the dominant cause. In older cities with original copper runs, corrosion-driven pinhole failure is most common.

Texas has the highest rate of residential slab leak detection calls of any US state, driven by a specific combination of factors: (1) Soil — the Texas Blackland Prairie and Gulf Coast Prairies sit on Vertisol clay soils with Plasticity Index values of 40–65, among the highest shrink-swell potential soils in the world. These soils undergo 3–6 inches of vertical movement per year between wet and dry seasons. (2) Construction — approximately 95% of Texas homes are built on slab foundations directly in contact with this soil, placing copper supply pipes in direct contact with soil that is constantly moving. (3) Climate — Texas experiences extended summer droughts that maximize soil desiccation and movement, followed by heavy rainfall that causes rapid re-expansion. (4) Pipe era — the bulk of the Texas housing stock was built between 1960 and 1990 with copper supply pipe that now has 30–60 years of service on highly mobile soil.

A professional slab leak detection appointment typically takes 1–3 hours on-site. The technician first performs an isolation test to confirm the leak is on the supply side (checking hot and cold lines separately) and to estimate flow rate. Acoustic detection involves placing sensors at multiple points on the floor and listening for the characteristic leak noise amplified through the concrete. In straightforward cases with good acoustic signal, the leak can be located within 60–90 minutes. Complex cases — thick slabs, multiple pipe runs, weak acoustic signal from PEX pipe — may require tracer gas as a secondary method, extending the appointment to 2–3 hours.

Polybutylene pipe is identifiable by its gray, blue, or black color — gray is most common for interior supply lines. Look under sinks, behind the water heater, and at the point where pipes enter walls. The pipe is typically 1/2 inch or 3/4 inch diameter with a dull, matte surface. Fittings are usually gray or white plastic (acetal) or aluminum. If your home was built between 1978 and 1995 and you see gray plastic supply lines, it is almost certainly polybutylene. You can also check the pipe labeling — polybutylene is often stamped 'PB2110'. If confirmed, consult with a licensed plumber about your replacement options — polybutylene was the subject of a class action settlement (Cox v. Shell Oil) specifically because of its documented failure rate.

Yes — most significant leaks are invisible at their source until substantial damage has occurred. Slab leaks are entirely under concrete. Underground service line leaks may not surface for months if the soil has good absorption capacity. Wall leaks from pinhole copper or failed shower pan liners discharge into wall cavities and subfloors, appearing only as staining, bubbling paint, or soft flooring. Leaks in unconditioned attic spaces may not manifest inside the living space until roof deck damage causes secondary intrusion. The absence of visible water is the primary reason leak detection technology exists — the purpose of acoustic, tracer gas, and thermal tools is to locate leaks that cannot be found by looking. An unexplained increase in water consumption confirmed by comparing monthly bills to the same period in prior years is often the only early indicator.

Tank-style water heaters have an average service life of 8–12 years. Tankless (on-demand) water heaters last 15–20 years with proper maintenance. Factors that shorten tank heater life: high mineral content water (hard water) accelerates scale buildup on heating elements and sediment accumulation; high pressure (above 80 PSI) stresses the tank; failure to flush the tank annually allows sediment accumulation that insulates the heating element and causes overheating. The anode rod — a magnesium or aluminum rod designed to corrode sacrificially to protect the tank lining — should be inspected every 3–5 years and replaced when depleted. A depleted anode rod is the most common cause of premature tank failure. Water heaters that are more than 10 years old and showing any signs of corrosion, discolored water, or unusual noise should be proactively replaced before a catastrophic tank rupture.

The Uniform Plumbing Code and International Plumbing Code both specify a maximum service pressure of 80 PSI for residential supply systems. Most appliance manufacturers void warranties on washing machine hoses, refrigerator water lines, and water heater supply valves at pressures above 80 PSI. Dishwasher fill valves and toilet fill valves are similarly rated for 80 PSI maximum. The optimal range for residential plumbing is 50–70 PSI — sufficient for good shower pressure and appliance performance while keeping stress on fittings and fixtures within safe limits. Below 40 PSI, shower performance degrades and some appliances may not fill correctly. Testing water pressure requires a simple gauge threaded onto a hose bib — available for under $15 at any home improvement store.