Leak Detection in Johnstown, Colorado

Yes. We connect Johnstown property owners and homeowners in Weld County with licensed leak detection specialists. Our network covers all of Colorado and is available for water leak detection, slab leak detection, underground pipe detection, hidden leak investigation, and emergency leak response. Call (844) 485-0339 to speak with a dispatcher who can connect you with an available specialist in your area.

In Johnstown, pipes in unheated spaces — crawlspaces, garages, exterior walls — are most vulnerable during hard freezes. A pipe that freezes may not burst immediately; freeze-thaw cycling creates micro-fractures that fail days or weeks later. If you experienced a freeze event and notice reduced pressure or unexplained moisture in Weld County, professional leak detection can find damage before it becomes a larger structural problem.

Galvanized pipes are not immediately dangerous in the way a gas leak is — they present a gradual risk that worsens over time. Galvanized steel pipe corrodes from the inside out. As zinc coating dissolves (typically after 40–50 years), rust accumulates on pipe walls, progressively reducing water flow, discoloring water, and ultimately causing pinhole failures or joint failures. The primary risks are: (1) water quality — orange or rust-colored water from galvanized pipes is a documented health concern as the rust can harbor bacteria and introduces iron above EPA aesthetic limits; (2) reduced flow — heavy rust buildup can reduce pipe diameter by 50–70% in severely corroded runs; (3) lead contamination risk — galvanized pipe used downstream of lead service lines can adsorb and release lead, a documented issue in cities with older municipal infrastructure. Homes with galvanized supply lines more than 50 years old should have them evaluated for replacement.

Texas has the highest rate of residential slab leak detection calls of any US state, driven by a specific combination of factors: (1) Soil — the Texas Blackland Prairie and Gulf Coast Prairies sit on Vertisol clay soils with Plasticity Index values of 40–65, among the highest shrink-swell potential soils in the world. These soils undergo 3–6 inches of vertical movement per year between wet and dry seasons. (2) Construction — approximately 95% of Texas homes are built on slab foundations directly in contact with this soil, placing copper supply pipes in direct contact with soil that is constantly moving. (3) Climate — Texas experiences extended summer droughts that maximize soil desiccation and movement, followed by heavy rainfall that causes rapid re-expansion. (4) Pipe era — the bulk of the Texas housing stock was built between 1960 and 1990 with copper supply pipe that now has 30–60 years of service on highly mobile soil.

A pressure reducing valve (PRV) is installed on the main water supply line entering the home to regulate incoming municipal water pressure down to a safe residential range (typically 60–80 PSI). Without a PRV, homes in high-pressure service zones (hillside neighborhoods, pump-boosted areas) can experience pressures of 100–150 PSI — far above what residential plumbing is designed for. PRV failure is a primary cause of pinhole leaks, appliance hose failures, and fixture seal failures. Signs of PRV failure: water pressure that feels excessively forceful, banging pipes (water hammer), repeatedly failing appliance supply hoses, or a water pressure gauge reading above 80 PSI. PRVs have a typical service life of 10–15 years and should be replaced proactively. Homes without a PRV in a high-pressure zone should have one installed — the cost is $250–$500 installed and can prevent thousands in damage.

The Uniform Plumbing Code and International Plumbing Code both specify a maximum service pressure of 80 PSI for residential supply systems. Most appliance manufacturers void warranties on washing machine hoses, refrigerator water lines, and water heater supply valves at pressures above 80 PSI. Dishwasher fill valves and toilet fill valves are similarly rated for 80 PSI maximum. The optimal range for residential plumbing is 50–70 PSI — sufficient for good shower pressure and appliance performance while keeping stress on fittings and fixtures within safe limits. Below 40 PSI, shower performance degrades and some appliances may not fill correctly. Testing water pressure requires a simple gauge threaded onto a hose bib — available for under $15 at any home improvement store.

Responsibility is typically split at the water meter, which sits at or near the property line. The municipal water utility owns and maintains everything from the water main in the street to the meter. The homeowner owns and is responsible for everything from the meter to the house — including the full underground service line run across the property. This is an important distinction because service line leaks on the homeowner's side are the homeowner's financial responsibility, and standard homeowners insurance (HO-3 policies) does not cover underground service line repair by default. A service line insurance endorsement — available from most insurers for $30–$60 per year — extends coverage to this exposure. Some utilities have begun offering service line protection programs as a billing add-on.

The most reliable early indicators are: (1) a water meter that continues to move after all fixtures are turned off — the meter test is the first self-check every homeowner should perform; (2) unexplained increases in your water bill without a change in usage; (3) warm or hot spots on floor surfaces (for hot water line leaks); (4) the sound of running water when no fixture is in use; (5) cracks appearing in interior walls or floor tiles, particularly in a linear pattern following a pipe run. Slab leaks from drain lines may not show water meter movement — instead they present as soft spots in flooring, musty odors, or unexplained moisture at baseboards. A professional acoustic or tracer gas test is needed to pinpoint the exact leak location before any repair.

Pipe freeze prevention depends on your home's construction type and local frost depth. For all homes: (1) Know where your main shutoff valve is and confirm it operates before winter; (2) Disconnect and drain garden hoses from exterior hose bibs — a connected hose traps water in the spigot and can freeze back into the supply line; (3) Insulate pipes in unheated spaces — garages, crawlspaces, and unconditioned attics. For homes in regions with frost depths below 15 inches (most of the South): (4) Let faucets drip slightly during freeze events — moving water is harder to freeze; (5) Open cabinet doors under sinks on exterior walls to allow heated room air to reach the pipes. For crawlspace homes: (6) Seal crawlspace vents before first freeze to trap ground warmth. For vacant properties: (7) Maintain minimum 55°F interior temperature or fully drain and blow out the supply system with compressed air.

Polybutylene pipe is identifiable by its gray, blue, or black color — gray is most common for interior supply lines. Look under sinks, behind the water heater, and at the point where pipes enter walls. The pipe is typically 1/2 inch or 3/4 inch diameter with a dull, matte surface. Fittings are usually gray or white plastic (acetal) or aluminum. If your home was built between 1978 and 1995 and you see gray plastic supply lines, it is almost certainly polybutylene. You can also check the pipe labeling — polybutylene is often stamped 'PB2110'. If confirmed, consult with a licensed plumber about your replacement options — polybutylene was the subject of a class action settlement (Cox v. Shell Oil) specifically because of its documented failure rate.